DeLonghi 10.13 User Manual

11

3.  Press the 

 button. “Disable?” is displayed (or “En-

able?” if the function has been disabled); 

4.  Press the 

 button to disable (or enable) the func-

tion.  

5.  Press the MENU/ESC button to exit the menu.
Warming the cups keeps the coffee hot. 

Energy Saving
Use this function to enable or disable energy saving mode.
When enabled, the function reduces energy consumption in 
compliance with European regulations. 
To disable (or enable) “energy saving” mode, proceed as 
follows:
1.  Press the MENU/ESC button to enter the menu;
2.  Press the HOT MILK or LATTE button (fig. 8) until “Energy 

saving” is displayed;

3.  Press the 

 button. “Disable?” is displayed (or “En-

able?” if the function has been disabled);

4.  Press the 

 button to disable (or enable) energy 

saving mode; 

5.  Then press the MENU/ESC  button to exit the menu.
When the function is enabled, if the machine is not used for 
about 1 minute, “Energy Saving” is displayed.

•  When  in  energy  saving  mode,  a  few  seconds  elapse

before the first coffee, cappuccino or milk based coffee is 
delivered as the appliance must heat up again.

•  To  prepare  any  drink,  press  any  button  to  exit  energy

saving, then press the button corresponding to the drink 
you want to make.

•  If  the  milk  container  is  inserted, “Energy  saving”  is  not

activated. 

Setting the temperature
To modify the temperature of the water used to make the cof-
fee, proceed as follows:
1.  Press the MENU/ESC button to enter the menu;
2.  Press the HOT MILK or LATTE button (fig. 8) until “Set 

temperature” is displayed;

3.  Press the

button;

4.   Press the HOT MILK or LATTE button until the required 

temperature (●= low; ●●●●= high) is displayed;

5.   Press the 

button to confirm;  

6.   Press the  MENU/ESC  button to exit the menu.

Setting water hardness
For instructions on setting water hardness, see page 20.

Beep
This enables or disables the beep emitted by the machine 
each time the buttons are pressed or an accessory is inserted/
removed. The beep is enabled by default.  
To disable or re-enable the beep, proceed as follows:
1.   Press the MENU/ESC button to enter the menu;
2.   Press the HOT MILK or LATTE button (fig. 8) until “Beep” 

is displayed;

3.  Press the 

 button. “ Disable?” or “ Enable?” is dis-

played; 

4.  Press the 

button to enable or disable the beep;

5.  Press the MENU/ESC button to exit the menu.

Setting the language 
To change the language for the display, proceed as follows:
1.   Press the MENU/ESC button to enter the menu;
2.   Press the HOT MILK or LATTE button (fig. 8) until “Set 

language” is displayed;

3.   Press the 

button;   

4.   Press the HOT MILK or LATTE button until the required 

language is displayed;

5.   Press the 

  button to confirm;   

6.  A message confirming the language installed is displayed;
7.   Then press the MENU/ESC  button to exit the menu. 

Cup lighting
This function enables or disables the cup lighting. The lighting 
is enabled by default.  
The lights come on each time coffee and drinks with milk are 
made and during each rinse cycle. 
To disable or re-enable this function, proceed as follows:
1.   Press the MENU/ESC button to enter the menu;
2.   Press the HOT MILK or LATTE button  (fig. 8) until “Cup 

lighting” is displayed.

3.  Press the  

 button. “ Disable?” or “ Enable?”  is dis-

played; 

4.  Press the 

 button to enable or disable the cup 

lighting; 

5.  Press the MENU/ESC button to exit the menu.

Default values (reset)
This resets all menu settings and programmed quantities back 
to the default values (with the exception of the language 
which remains as previously set). 
To reset the default values, proceed as follows:
1.   Press the MENU/ESC button to enter the menu;
2.   Press the  HOT MILK or LATTE button (fig. 8) until “De-

fault values” is displayed;

3.   Press the 

 button;

4.   The message “Confirm?” is displayed.