Alcatel-Lucent 6850-48 Reference Guide
PIM Commands
page 45-54
OmniSwitch CLI Reference Guide
September 2009
Stub Interface = false,
Prune Limit Interval = 60,
Graft Retry Interval = 3,
State Refresh Enabled = true,
Operational Status = disabled
output definitions
Interface Name
The name of the interface on which PIM is enabled.
IP address
Specifies the IP address of the specified interface.
Designated Router
The 32-bit IP address for the Designated Router (DR). The DR acts on
behalf of any directly-connected hosts with respect to the PIM-SM
protocol. Only one router in the LAN will act as the DR.
behalf of any directly-connected hosts with respect to the PIM-SM
protocol. Only one router in the LAN will act as the DR.
Hello Interval
The frequency at which PIM Hello messages are transmitted on a spec-
ified interface. Values may range from 1 to 18000. The default value
is 30.
ified interface. Values may range from 1 to 18000. The default value
is 30.
Join/Prune Interval
The Join/Prune interval for the associated interface. The Join/Prune
interval is the interval at which periodic PIM-SM Join/Prune messages
are sent. Values may range from 1 to 18000.
interval is the interval at which periodic PIM-SM Join/Prune messages
are sent. Values may range from 1 to 18000.
Triggered Hello Interval
The current Triggered Hello Interval. This value indicates the maxi-
mum time, in seconds, before a triggered PIM Hello message is trans-
mitted on the corresponding interface. Values may range from 1 to 60.
The default value is 5.
mum time, in seconds, before a triggered PIM Hello message is trans-
mitted on the corresponding interface. Values may range from 1 to 60.
The default value is 5.
Hello Holdtime
The current Hello Holdtime value. This value indicates the maximum
amount of time, in seconds, Hello messages will be held before they are
considered invalid. Values may range from 0 to 65535. The default
value is 105.
amount of time, in seconds, Hello messages will be held before they are
considered invalid. Values may range from 0 to 65535. The default
value is 105.
Join/Prune Holdtime
The current Join/Prune Holdtime value. This value indicates the maxi-
mum amount of time, in seconds, Join/Prune messages will be held
before they are considered invalid. Values may range from 0 to 65535.
The default value is 210.
mum amount of time, in seconds, Join/Prune messages will be held
before they are considered invalid. Values may range from 0 to 65535.
The default value is 210.
Propagation Delay
The expected propagation delay between PIM routers on this network.
Override Interval
The current Override Interval. This value is used to avoid synchroniza-
tion of override messages when multiple downstream routers share a
multi-access link. The sending of override messages is delayed at ran-
dom time intervals. The amount of randomization used by a router is
dictated by this number. Values may range from 0 to 65535. The
default value is 2500.
tion of override messages when multiple downstream routers share a
multi-access link. The sending of override messages is delayed at ran-
dom time intervals. The amount of randomization used by a router is
dictated by this number. Values may range from 0 to 65535. The
default value is 2500.
Generation ID Option
The value of the Generation ID this router inserted in the last PIM
Hello message it sent on this interface.
Hello message it sent on this interface.
DR Priority
Displays the Designated Router priority for each interface. This value is
used in determining the Designated Router on an interface. Values may
range from 1 to 192. A higher numeric value denotes a higher priority.
Note that priority-based election is used only if all routers on the inter-
face are using the DR priority option. The default value is 1.
used in determining the Designated Router on an interface. Values may
range from 1 to 192. A higher numeric value denotes a higher priority.
Note that priority-based election is used only if all routers on the inter-
face are using the DR priority option. The default value is 1.
Lan Delay Enabled
Options include true and false. The value will be true if all neighbors
on the interface are using the LAN Prune Delay option. Otherwise, the
setting will be false.
on the interface are using the LAN Prune Delay option. Otherwise, the
setting will be false.
Effective Propagation Delay
The Effective Propagation Delay on this interface.