Pioneer VSX-920-K User Guide
Additional information
11
73
En
English
Français
Deutsch
Nederlands
Italiano
Español
No sound from subwoofer.
• Make sure the subwoofer is switched on.
• If the subwoofer has a volume knob, make sure it’s turned up.
• The Dolby Digital or DTS source you are listening to may not have an
LFE channel.
• Switch the subwoofer setting in Speaker Setting on page 45 to
• If the subwoofer has a volume knob, make sure it’s turned up.
• The Dolby Digital or DTS source you are listening to may not have an
LFE channel.
• Switch the subwoofer setting in Speaker Setting on page 45 to
YES or
PLUS.
• Switch the LFE ATT (LFE Attenuate) on page 41 to
• Switch the LFE ATT (LFE Attenuate) on page 41 to
LFEATT 0 or LFEATT 5.
No sound from surround or
center speakers.
center speakers.
• Connect the speakers properly (refer to page 19).
• Refer to Speaker Setting on page 45 to check the speaker settings.
• Refer to Channel Level on page 47 to check the speaker levels.
• Refer to Speaker Setting on page 45 to check the speaker settings.
• Refer to Channel Level on page 47 to check the speaker levels.
The
PHASE CONTROL
feature doesn’t seem to
have an audible effect.
have an audible effect.
• If applicable, check that the lowpass filter switch on your subwoofer is
off, or the lowpass cutoff is set to the highest frequency setting. If there is
a
off, or the lowpass cutoff is set to the highest frequency setting. If there is
a
PHASE setting on your subwoofer, set it to 0º (or depending on the
subwoofer, the setting where you think it has the best overall effect on the
sound).
• Make sure the speaker distance setting is correct for all speakers (see
Speaker Distance on page 48).
sound).
• Make sure the speaker distance setting is correct for all speakers (see
Speaker Distance on page 48).
Considerable noise in radio
broadcasts.
broadcasts.
• Connect the antenna (page 29) and adjust the position for best
reception.
• Route any loose cables away from the antenna terminals and wires.
• Fully extend the FM wire antenna, position for best reception, and
secure to a wall (or connect an outdoor FM antenna).
• Connect an additional internal or external AM antenna (page 29).
• Turn off equipment causing interference or move it away from the
receiver (or move antennas farther away from equipment causing noise).
reception.
• Route any loose cables away from the antenna terminals and wires.
• Fully extend the FM wire antenna, position for best reception, and
secure to a wall (or connect an outdoor FM antenna).
• Connect an additional internal or external AM antenna (page 29).
• Turn off equipment causing interference or move it away from the
receiver (or move antennas farther away from equipment causing noise).
Broadcast stations cannot
be selected automatically.
be selected automatically.
• Connect an outdoor antenna (refer to page 29).
Noise during playback of a
cassette deck.
cassette deck.
• Move the cassette deck away from your receiver, until the noise
disappears.
disappears.
Sound is produced from
other components, but not
from LD or DVD player.
other components, but not
from LD or DVD player.
• Set the
SIGNAL SEL to HDMI, C1/O1/O2 (DIGITAL) or A (analog)
according to the type of connections made (refer to page 43).
• Set the digital input settings correctly (refer to page 48).
• Make digital connections (refer to page 24) and set the
• Set the digital input settings correctly (refer to page 48).
• Make digital connections (refer to page 24) and set the
SIGNAL SEL to
C1/O1/O2 (DIGITAL) (refer to page 43).
• Refer to the instruction manual supplied with the DVD player.
• Refer to the instruction manual supplied with the DVD player.
No sound is output or a
noise is output when
software with DTS is played
back.
noise is output when
software with DTS is played
back.
• Set the digital volume level of the player to full, or to the neutral
position.
• Make sure the player’s settings are correct and/or the DTS signal out is
on. Refer to the instruction manual supplied with the DVD player.
• Set the input signal type to
position.
• Make sure the player’s settings are correct and/or the DTS signal out is
on. Refer to the instruction manual supplied with the DVD player.
• Set the input signal type to
C1/O1/O2 (DIGITAL) (see Choosing the
input signal on page 43).
Problem
Remedy
VSX-920_UCSMXCN_En.book 73 ページ 2010年1月21日 木曜日 午前9時43分