Cisco Cisco ASR 5000
Exec Mode show Commands (Q-S)
▀ show subscribers
▄ Command Line Interface Reference, StarOS Release 18
4960
session-time-left, sgsn-address, sgsn-service,
sgw-address, sgw-
service,
tx-data, username, verbose, grep, more
access-flows { accounting | dynamic |
pre-provisioned |
static }
Shows the ip-flows for the subscribers defined by the specified filter keywords.
accounting
: displays the accounting type of access flows for a subscriber.
dynamic
: displays the dynamic type of access flows for a subscriber.
pre-provisioned
: displays the pre-provisioned type of access flows for a WiMAX subscriber.
static
: displays the static type of access flows for a subscriber.
The following filter keywords are valid with this command:
active, active-charging-service, all,
apn, asn-peer-address, asngw-
service, asnpc-service,
callid, card-num, ccoa-only, configured-idle-
timeout, connected-time,
dhcp-server,
dormant,
epdg-address, epdg-
service,
fa, fa-service, flow-type, ggsn-service,
gprs-service,
gsm-
traffic-class, ha, ha-ipsec-only, ha-service,
hnbgw-only, hsgw-
service,
idle-time, imsi, ip-address, ip-pool, ipv6-address, ipv6-
prefix, l3-tunnel-local-address, l3-tunnel-remote-address, lac, lac-
service,
service,
lma-service,
lns, lns-service, long-duration-time-left,
mag-
service,
mip-udp-tunnel-only,
mme-address, mme-service,
msid, msisdn,
network-requested, network-type, pcf,
pdg-service, pdif-service,
pdsn-
service,
pgw-address, plmn-type,
rulebase, rx-data, session-time-left,
sgsn-address, sgsn-service, sgw-address, sgw-service,
tx-data,
username, verbose, grep, more
access-type { lxcdma | ehrpd | lte | undetemrined | wcdma | wifi | wired }
Displays active subscribers using a specific type of UE.
1xcdma
: 1XCDMA – Wireless CDMA 1x high speed internet service
ehrpd
: eHRPD – Enhanced High Rate Packet Data
evdo
: EvDO – EVolution-Data Optimized
lte
: LTE – Long Term Evolution
undetermined
wcdma
: WCDMA – Wideband Code Division Multiple Access
wifi
: WiFi – Wireless local area network
wired
The following filter keywords are valid with this command:
access-type, bearer-establishment, bng-service, callid, card-num,
configured-idle-timeout, cscf-service, domain, ebi, enodeb-address, fa,
firewall, fw-and-nat, gtp-version, gtpu-bind-address, gtpu-service, ha,
hnbgw-service, idle-time, ims-auth-service, imsi, ip-address, ip-alloc-
method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-
tunnel-remote-addr, long-duration-time-left, mipv6ha-service, msid, nat,
network-type, profile-id, profile-name, qci, rx-data, s1u-state,
configured-idle-timeout, cscf-service, domain, ebi, enodeb-address, fa,
firewall, fw-and-nat, gtp-version, gtpu-bind-address, gtpu-service, ha,
hnbgw-service, idle-time, ims-auth-service, imsi, ip-address, ip-alloc-
method, ip-pool, ipv6-address, ipv6-prefix, l3-tunnel-local-addr, l3-
tunnel-remote-addr, long-duration-time-left, mipv6ha-service, msid, nat,
network-type, profile-id, profile-name, qci, rx-data, s1u-state,