Cisco Cisco ASR 5000

 

security-type, session-time-left, sgw-address, smgr-instance, tx-data, 
ue-type, username, grep, more 

 

Displays active subscribers. When no Filter Keywords are specified, the output is a summary of all active 
subscribers. When Filter Keywords are specified, the percentage is displayed as graphs in which one is 
displayed using a high sampling rate, a 10-second interval between samples, and a low sampling rate, a 15-
minute interval between samples. 
The following filter keywords are valid with this command: 

apn, asn-peer-address, asngw-service, asnpc-service, 

bearer-

establishment, bng-service, callid, card-num, ccoa-only, configured-idle-
timeout, connected-time, 

dhcp-server, 

ebi, 

epdg-address, epdg-

service, 

fa, fa-service, firewall, fw-and-nat, ggsn-service, 

gprs-

service, 

gsm-traffic-class, gtp-version, gtpu-bind-address, gtpu-

service, ha, ha-ipsec-only, ha-service, 

hsgw-service, 

idle-time, imei, 

ims-auth-service, imsi, ip-address, ip-pool, ipv6-address, ipv6-prefix, 
l3-tunnel-local-addr, l3-tunnel-remote-addr, lac, lac-service, 

lma-

service, 

lns, lns-service, long-duration-time-left, 

mag-service, mme-

address, mme-service, 

msid, msisdn, nat, nemo-only, network-requested, 

pcf, 

pdg-service, pdif-service, 

pdsn-service, 

pgw-address, plmn-

type, 

profile-id, profile-name, qci, rx-data, s1u-state, session-time-

left, 

sgsn-address, sgsn-service, 

smgr-instance, 

sgw-address, sgw-

service, 

tx-data, username, grep, more 

 

Displays information for subscribers being processed by the active charging service specified as an 
alphanumeric string of 1 through 15 characters. 
The following filter keywords are valid with this command: 

active-charging-service, bandwidth-policy, bearer-establishment, bng-
service, callid, card-num, cbb-policy, configured-idle-timeout, 
connected-time, ebi, enodeb-address,

epdg-address, epdg-service, 

 fa, 

firewall, fw-and-nat, gtp-version, gtpu-bind-address, gtpu-service, ha, 
idle-time, ims-auth-service, imsi, ip-address, ip-pool, ipv6-address, 
ipv6-prefix, l3-tunnel-local-address, l3-tunnel-remote-address, long-
duration-time-left, mag-service, mipv6ha-service, msid, nat, network-
type, profile-id, profile-name, qci, rulebase, rx-data, s1u-state, s5-
proto, session-time-left, sgw-address, smgr-instance, tx-data, username, 
grep, more 

 

Displays subscriber link activity percentage. When no Filter Keywords are specified, the output is a summary 
of all subscriber activity. When Filter Keywords are specified, the link activity percentage is displayed as 
graphs in which one is displayed using a high sampling rate, a 10-second interval between samples, and a low 
sampling rate, a 15-minute interval between samples. 
The following filter keywords are valid with this command: 

active, all, 

apn, asn-peer-address, asngw-service, asnpc-service, 

bearer-establishment, bng-service, callid, card-num, ccoa-only, 
configured-idle-timeout, connected-time, 

dhcp-server, 

dormant, ebi,