JVC 0210TTH-SW-VP User Manual
31
5
Adjust the focus
You can adjust the focus using the
AFocusB item of the
Lens menu.
To move the focus point closer:
Press the
A+B (Near) end of AFocusB
To move the focus point away:
Press the
AB (Far) end of AFocusB
NOTE:
● The focus changes each time you click on the inner
buttons ( / ). (Fine control)
The outer buttons ( / ) change the focus when they
are depressed. (Coarse control)
The outer buttons ( / ) change the focus when they
are depressed. (Coarse control)
6
Select a screen mode for projection
You can specify the screen mode using
ADisplay
Mode
B of the Setting menu. (A Page 38)
NOTE:
● The projected image varies according to the mode of
connection. (
7
Click the
AOFFB button under the APowerB
item of the Main menu to end the projection
● The projector switches to the cool down mode, and
the [STANDBY/ON] indicator appears blinking in
red.
red.
● A gray image will be displayed for a maximum
duration of 2 minutes during the ending process
only after several hours of image projection. The
lamp starts cooling down thereafter.
only after several hours of image projection. The
lamp starts cooling down thereafter.
● After exiting the cool down mode, the projector
switches automatically to the standby mode, and
the [STANDBY/ON] indicator lights up in red.
the [STANDBY/ON] indicator lights up in red.
● You can also turn off the power by pressing the
[OPERATE I/
B] button on the projector unit for
more than one second.
8
Turn the main power at the rear of the
projector unit to off [O]
● The [STANDBY/ON] indicator on the projector unit
goes off.
CAUTION:
● Do not turn off the main power supply switch when in
the cool down mode. Doing so may shorten the lamp
life and cause a malfunction.
life and cause a malfunction.
● Upon using, attach the lens cap to prevent soiling of
the lens.
● When the projector is not to be used for a long time,
disconnect the power plug.
Useful Features During Projection
Hiding the projected image temporarily
The projected image can be hidden by clicking the
AONB
button under the
AHideB item of the Main menu or Image
menu.
● When the image is not displayed, pressing AOFFB
under the
AHideB item to display the hidden image.
NOTE:
● When the image is hidden, the [STANDBY/ON]
indicator appears blinking in green.
Cool down mode
The cool down mode is a function that cools down the
lamp for an interval of about 180 seconds after
projection ends (ending process).
This function is to prevent deformation and damage of
the internal components of the projector due to heat
from the overheated lamp. It also prevents lamp
breakage and shortened lamp life.
lamp for an interval of about 180 seconds after
projection ends (ending process).
This function is to prevent deformation and damage of
the internal components of the projector due to heat
from the overheated lamp. It also prevents lamp
breakage and shortened lamp life.
● When the projector is in the cool down mode, the
[STANDBY/ON] indicator appears blinking in red.
● Do not shut down the main power supply or unplug
the power cord when in the cool down mode. Also,
do not block the air inlets and vent holes. Doing so
may shorten the lamp life and cause a malfunction.
do not block the air inlets and vent holes. Doing so
may shorten the lamp life and cause a malfunction.
Setting
Convergence
Lens
Option
Logout
host PJ-1
user: root
user: root
Input Level
Main
Image
0-255(PC)
Display Mode
16-235
1
1
3
3
1
2
4
Brightness
Setting
Convergence
Lens
Option
Logout
host PJ-1
user: root
user: root
Red
0
-30
+30
Green
0
-30
+30
Blue
0
-30
+30
Contrast
Gamma
Hide
Red
0
-30
+30
Green
0
-30
+30
Blue
0
-30
+30
Main
Image
ON
OFF
B
C
A