Manualsbrain.com
  1. Manuals
  2. Brands
  3. Yamaha
  4. yamaha digital sound projector ysp3300
  5. User Manual

Yamaha yamaha digital sound projector ysp3300 User Manual

Download
Page of 80
Initial settings
27
 En
PR
EPARA
TION
PL
AYBACK
SET
TINGS
TRO
UBLE
SHO
OTI
NG
A
PPEN
DIX
If an error message is displayed on the TV screen, see “Error 
messages” below to determine the cause and resolve the problem. 
Follow the instructions below to begin measurement again. 
[ERROR E-1]
Press the ENTER key to run the AUTO SETUP procedure again. 
Or press the X key to continue the measurement.
[ERROR E-7]
Press the 
 key to turn this unit to the standby mode, then run 
AUTO SETUP procedure again after turning this unit on.
[ERROR E-9]
1 Be sure that a wireless connection between the subwoofer and 
center unit has been established (
2 Press the RETURN key.
The “IntelliBeam” menu is displayed.
3 Select “BEAM+SOUND OPTIMIZE”, “BEAM OPTIMIZE 
ONLY”, or “SOUND OPTIMIZE ONLY” and press the X 
key.
1)
4 Follow steps 4, 5, and 6 to measure again (
[ERROR E-2] through [ERROR E-6]
1 Press the RETURN key.
The “IntelliBeam” menu is displayed.
2 Select “BEAM+SOUND OPTIMIZE”, “BEAM OPTIMIZE 
ONLY”, or “SOUND OPTIMIZE ONLY” and press the X 
key.
1)
3 Follow steps 4, 5, and 6 to measure again (
Error messages
If an error message is displayed
ERROR E-1: Please test in quieter environment.
Cause
Remedy
There is too much noise in your 
listening room.
Make sure that your listening 
room is as quiet as possible. You 
may want to choose certain hours 
during the day when there is not 
much noise coming from outside.
ERROR E-2: No MIC detected. Please check MIC 
connection and re-try.
Cause
Remedy
The IntelliBeam microphone is 
disconnected.
Connect the IntelliBeam 
microphone to the 
INTELLIBEAM MIC jack on the 
rear of this unit and begin 
measurement again.
ERROR E-3: Unexpected control is detected. Please 
re-try.
Cause
Remedy
Some other operations were 
performed on this unit.
Begin measurement again. Do 
not perform any other operations 
with this unit during 
measurement.
ERROR E-4: Please check MIC position. MIC should 
be set in front of Sound Projector. Please re-try.
Cause
Remedy
The IntelliBeam microphone is 
not placed in front of this unit.
Position the IntelliBeam 
microphone in front of this unit 
and begin measurement again.
ERROR E-5: Please check MIC position. MIC should 
be set above 1.8m/6.0ft and re-try.
Cause
Remedy
The IntelliBeam microphone is 
not placed in the right distance 
from this unit.
Position the IntelliBeam 
microphone at a distance of more 
than 1.8 m (6.0 ft) from this unit 
and begin measurement again.
ERROR E-6: Volume level is lower than expected. 
Please check MIC position/connection and re-try.
Cause
Remedy
The IntelliBeam microphone 
cannot collect the sound 
produced by this unit.
Position the IntelliBeam 
microphone properly, check the 
connection, and then begin 
measurement again.
ERROR E-7: Unexpected error happened. Please 
turn off and re-try.
Cause
Remedy
An internal system error 
occurred.
Press the 
 key to turn this unit 
to the standby mode, then run 
AUTO SETUP procedure again 
after turning this unit on.
ERROR E-9: Check the connection with subwoofer.
Cause
Remedy
The subwoofer is not connected 
wirelessly.
Be sure that a wireless 
connection between the 
subwoofer and center unit has 
been established (
measure again.