Panasonic KXTG6621FX Operating Guide
Programming
28
5
{i
c}
L
When the night mode is set, 3 is
displayed.
displayed.
Changing the start and end time
1
8(237
2
Continue from step 3, “Turning night
mode on/off”, page 27.
mode on/off”, page 27.
Setting the ring delay
This setting allows the handset to ring during
night mode if the caller waits long enough.
After the selected amount of time passes, the
handset rings. If you select “No Ringing”,
night mode if the caller waits long enough.
After the selected amount of time passes, the
handset rings. If you select “No Ringing”,
the handset never rings during night mode.
1
8(239
2
{
r}
: Select the desired setting. s M
s
{ic}
Note:
L
L
When the answering system answers the
call, this feature does not work.
(KX-TG6621)
call, this feature does not work.
(KX-TG6621)
Changing the handset name
Each handset can be given a customised
name (“Bob”, “Kitchen”, etc.). This is useful
when you make intercom calls between
handsets. You can also select whether or not
the handset name is displayed in standby
mode. The default setting is “No”. If you select
name (“Bob”, “Kitchen”, etc.). This is useful
when you make intercom calls between
handsets. You can also select whether or not
the handset name is displayed in standby
mode. The default setting is “No”. If you select
“Yes” without entering any handset name,
“Handset 1” to “Handset 6” is displayed.
1
8(1)4
2
If not required, go to step 3.
3
M
4
{
r}
: Select the desired setting. s M 2
times
5
{i
c}
Incoming call barring (Caller ID
subscribers only)
subscribers only)
This feature allows the unit to reject calls from
specified phone numbers that you do not want
to answer such as junk calls.
specified phone numbers that you do not want
to answer such as junk calls.
When a call is received, the unit does not ring
while the caller is being identified. If the phone
number matches an entry in the call barred list,
the unit sends out a busy tone to the caller, and
then disconnects the call.
Important:
L
while the caller is being identified. If the phone
number matches an entry in the call barred list,
the unit sends out a busy tone to the caller, and
then disconnects the call.
Important:
L
When the unit receives a call from a number
that is stored in the call barred list, the call is
logged in the caller list (page 32) with 7
after the call is disconnected.
that is stored in the call barred list, the call is
logged in the caller list (page 32) with 7
after the call is disconnected.
Storing unwanted callers
You can store up to 30 phone numbers in the
call barred list.
Important:
L
call barred list.
Important:
L
You must store the phone number with an
area code in the call barred list.
area code in the call barred list.
■ From the caller list:
1
{<}
(y)
2
{
r}
: Select the entry to be barred. s
I
3
{
r}
: “Caller Barred” s M
4
{
r}
: “Yes” s M s {ic}
■ By entering phone numbers:
1
8(217
s m
2
Enter the phone number (24 digits
max.). s M
L
max.). s M
L
To erase a digit, press ^.
3
{i
c}
Viewing/editing/erasing bar call
numbers
numbers
1
8(217
2
{
r}
: Select the desired entry.
L
To exit, press {ic}.
3
To edit a number:
~
~
s Edit the phone number. s M
s
{ic}
To erase a number:
W
W
s {r}: “Yes” s M s {ic}
Note:
L
L
When editing, press the desired dial key to
add, ^ to erase.
add, ^ to erase.
TG661x_662xFX(e).book Page 28 Wednesday, March 2, 2011 2:31 PM