Panasonic KXFC195GRG Operating Guide
7. Programmable Features
49
Code #06: Changing the ring setting in
TAD/FAX mode
TAD/FAX mode
TAD RING COUNT
RINGS=2
RINGS=2
[
±]
To change the number of rings before the unit
answers a call in TAD/FAX mode. You can select
“1”, “2” (default), “3”, “4”, “TOLL SAVER” or
“RINGER OFF”. See page 38 for details.
answers a call in TAD/FAX mode. You can select
“1”, “2” (default), “3”, “4”, “TOLL SAVER” or
“RINGER OFF”. See page 38 for details.
L
Set feature #77 to “TAD/FAX” (page 52)
beforehand.
beforehand.
Code #06: Changing the ring setting in FAX
ONLY mode
ONLY mode
FAX RING COUNT
RINGS=2
RINGS=2
[
±]
To change the number of rings before the unit
answers a call in FAX ONLY mode.
You can select “1”, “2” (default), “3”, “4”, “5”, “6”,
“7”, “8” or “9”.
answers a call in FAX ONLY mode.
You can select “1”, “2” (default), “3”, “4”, “5”, “6”,
“7”, “8” or “9”.
L
Set feature #77 to “FAX ONLY” (page 52)
beforehand.
beforehand.
Code #10: Changing the maximum incoming
message recording time
message recording time
RECORDING TIME
=VOX
=VOX
[
±]
“VOX” (default): Unlimited.
“1-9 MIN”: 1 minute to 9 minutes.
“1-9 MIN”: 1 minute to 9 minutes.
Code #11: Setting the remote operation ID
REMOTE TAD ID
=ON
=ON
[
±]
1. Press {MENU}.
2. Press {<} or {>} repeatedly to select this
feature.
3. Press {A} or {B} repeatedly to select “ON”.
4. Press {SET}.
5. Enter any 3-digit number except a number
using 0 or 7.
L
The default ID is “111”.
6. Press {SET}.
7. Press {MENU}.
Code #13: Setting the dialling mode
DIALLING MODE
=TONE
=TONE
[
±]
If you cannot dial, change this setting depending
on your telephone line service.
“TONE”(default): For tone dial service.
“PULSE”: For rotary pulse dial service.
on your telephone line service.
“TONE”(default): For tone dial service.
“PULSE”: For rotary pulse dial service.
L
You must set the dialling mode for both the
base unit and the handset (page 57).
base unit and the handset (page 57).
Code #17: Setting the ringer pattern
RINGER PATTERN
=A
=A
[
±]
You can select “A” (default), “B” or “C”.
Code #19: Setting the clock entry/display
CLOCK DISPLAY
=12H
=12H
[
±]
This feature changes the clock format for when
the line is indicated in printed reports and lists, or
displayed on the base unit.
“12H” (default): 12 hour clock
“24H”: 24 hour clock
the line is indicated in printed reports and lists, or
displayed on the base unit.
“12H” (default): 12 hour clock
“24H”: 24 hour clock
7.3 Advanced features
Code #22: Setting the journal report to print
automatically
automatically
AUTO JOURNAL
=ON
=ON
[
±]
“ON” (default): The unit will print a journal report
automatically after every 30 new fax
communications (page 34).
“OFF”: The unit will not print a journal report, but
will keep a record of the last 30 fax
communications.
automatically after every 30 new fax
communications (page 34).
“OFF”: The unit will not print a journal report, but
will keep a record of the last 30 fax
communications.
Code #23: Sending documents overseas
OVERSEAS MODE
=OFF
=OFF
[
±]
If you have difficulty sending an overseas fax,
activate this feature before starting transmission.
activate this feature before starting transmission.
L
This feature is not available for broadcast
transmission.
transmission.
L
The calling charge may be higher as the
transmission speed is slowed down.
transmission speed is slowed down.
“ON”: After transmission, this feature will turn off
automatically.
“OFF” (default): Deactivates this feature.
automatically.
“OFF” (default): Deactivates this feature.
Code #25: Sending a fax at a specific time
DELAYED SEND
=OFF
=OFF
[
±]
This feature allows you to take advantage of low-
cost calling hours offered by your telephone
company. This feature can be set up to 24 hours
in advance of the desired time.
To send a document:
cost calling hours offered by your telephone
company. This feature can be set up to 24 hours
in advance of the desired time.
To send a document:
1. Insert the document.
2. Press {MENU}.
3. Press {#} then {2}{5}.
FC195GR.book Page 49 Wednesday, April 2, 2003 11:39 AM