JTECH Communications Inc. SERIES2600 User Manual
JTECH UHF Desktop Transmitter Installation and Operation Guide 320115K
Page 29
In the preceding chart, the features ask questions and use detailed messages.
The messages and their meanings are explained below:
Prompt Meaning
The messages and their meanings are explained below:
Prompt Meaning
Enter Pager #
This message is the ‘Home Position’ of the Desktop Unit.
All other modes start here and are called to the screen by
pressing *’s to scroll down through the menu entries. To
page a pager or its replacement, enter the original ‘old’
pager number here. That pager number may be followed
by an * and then up to a 16 digit optional message and a
# sign, or the pager number may be followed directly by a
# sign for the vibe/tone pagers. This entry is also
accepted from the telephone on the PeopleAlert with
Telephone.
All other modes start here and are called to the screen by
pressing *’s to scroll down through the menu entries. To
page a pager or its replacement, enter the original ‘old’
pager number here. That pager number may be followed
by an * and then up to a 16 digit optional message and a
# sign, or the pager number may be followed directly by a
# sign for the vibe/tone pagers. This entry is also
accepted from the telephone on the PeopleAlert with
Telephone.
Enter Grp # __
Enter a group number 1 – 99 to page a group. This is
followed by an *, an optional message and a #. This
entry proceeded by the '*' is also accepted from the
telephone on the PeopleAlert with Telephone.
followed by an *, an optional message and a #. This
entry proceeded by the '*' is also accepted from the
telephone on the PeopleAlert with Telephone.
Unit Stats
Touching the # key at this prompt will display statistics
including total number of transmits, number of pages
sent from the keypad, number of pages sent from the
telephone and the number of times the transmitter has
been powered up.
including total number of transmits, number of pages
sent from the keypad, number of pages sent from the
telephone and the number of times the transmitter has
been powered up.
Password
This protects the balance of menu access by requiring a
4-digit password to be entered. The factory default is
1234. (A subsequent menu prompt allows for changing
of this password.)
4-digit password to be entered. The factory default is
1234. (A subsequent menu prompt allows for changing
of this password.)
Turn Off Pagers?
Prompt to turn off all RapidCall Vibe/Tone pagers via an
Over-the-Air (OTA) transmission.
Over-the-Air (OTA) transmission.
Old Pager #
Enter the pager number to be replaced (1- 4 digits)
New Pager #
Enter the pager number that will replace the old pager (1-
4 digits)
4 digits)
Enter Digit
You have pressed something other than a number key
when a number key was expected.
when a number key was expected.
1= POC Vib
2= Glwstr
2= Glwstr
Enter a one for a RapidCall (POCSAG) vibe/tone pager
or two for a Glowster pager. To see the next prompt,
press #. (3 or 4 may be pressed at this time without
waiting for the next prompt.)
or two for a Glowster pager. To see the next prompt,
press #. (3 or 4 may be pressed at this time without
waiting for the next prompt.)
3= Numeric
4= Alpha
4= Alpha
Enter a three for a RapidCall Numeric pager or four for
an alphanumeric pager (one that can display letters as
well as numbers). You can also press 1 or 2 at this
prompt for POCSAG Vibe or Glowster pagers.
an alphanumeric pager (one that can display letters as
well as numbers). You can also press 1 or 2 at this
prompt for POCSAG Vibe or Glowster pagers.
Replace Pager
This can add an entry to the Replace Pager table so that
every time the old pager number is designated to be
transmitted, the new pager number will replace it. A
pager may also be removed from the Replace Table by
entering the old pager number used to set up the original
replace followed by a new pager number of 0 (1 - 4 digits
of 0). Some of the other screens presented during this
mode are also explained in this chart.
every time the old pager number is designated to be
transmitted, the new pager number will replace it. A
pager may also be removed from the Replace Table by
entering the old pager number used to set up the original
replace followed by a new pager number of 0 (1 - 4 digits
of 0). Some of the other screens presented during this
mode are also explained in this chart.