JTECH Communications Inc. SERIES2600 User Manual
JTECH UHF Desktop Transmitter Installation and Operation Guide 320115K
Page 28
Function Description
Send All Call
Scroll Down *
Scroll Down *
Sends a page to all RapidCall vibe/tone, Glowster and CommPass
pagers. Press the # key to send the command. ‘Sending All Call’
appears in the display, indicating the command has been sent.
Alternately, this command can be sent by entering “9998#” at the
enter pager screen.
pagers. Press the # key to send the command. ‘Sending All Call’
appears in the display, indicating the command has been sent.
Alternately, this command can be sent by entering “9998#” at the
enter pager screen.
Range Test
Scroll Down *
Scroll Down *
This feature allows you to conduct a range test. A range test is
provided to verify the coverage area. Press # to turn on range test
mode. The PeopleAlert then asks for the pager ID number to be
used for the test. For example:
To use RapidCall vibration/tone pager number 12, press “12 #”.
To use RapidCall numeric pager number 12, press “12 * #”.
The Desktop Transmitter display will alternate between ‘Num (or
Vib) 12 Testing’ and ‘Enter Pager #’. The range test page will be
sent approximately every 15 seconds. To exit the range test mode,
press * #. This key sequence brings up the special function menu
for the range test feature and then turns if off. One pager at a time
can be used for range testing.
provided to verify the coverage area. Press # to turn on range test
mode. The PeopleAlert then asks for the pager ID number to be
used for the test. For example:
To use RapidCall vibration/tone pager number 12, press “12 #”.
To use RapidCall numeric pager number 12, press “12 * #”.
The Desktop Transmitter display will alternate between ‘Num (or
Vib) 12 Testing’ and ‘Enter Pager #’. The range test page will be
sent approximately every 15 seconds. To exit the range test mode,
press * #. This key sequence brings up the special function menu
for the range test feature and then turns if off. One pager at a time
can be used for range testing.
Search Mode?
Scroll Down *
Scroll Down *
This feature allows for Glowster and CommPass pagers to be
located in the coverage area. To activate, simply press the # key
at the Search prompt. Glowsters off the charging rack within the
coverage area will respond with a tone. Glowsters with Voice and
CommPass family pagers will respond with the appropriate voice
message. Touch any key to exit search mode.
located in the coverage area. To activate, simply press the # key
at the Search prompt. Glowsters off the charging rack within the
coverage area will respond with a tone. Glowsters with Voice and
CommPass family pagers will respond with the appropriate voice
message. Touch any key to exit search mode.
Default # of
Vibes
Scroll Down *
Vibes
Scroll Down *
This feature allows for alerts 1-9 to be selected for the standard
default alert for pages sent. This should always be set to a
number between 1 and 5, corresponding to Alerts 1 – 5 as defined
on Table 1. The factory default setting is 3.
default alert for pages sent. This should always be set to a
number between 1 and 5, corresponding to Alerts 1 – 5 as defined
on Table 1. The factory default setting is 3.
Audible ON/OFF
Scroll Down *
Scroll Down *
This feature is used to turn ON or OFF the audible tone alerts as
well as the voice table ready alert. Glowsters or CommPass
family pagers must be off/out of the charger and not stacked to be
able to ‘hear’ this OTA programming change.
well as the voice table ready alert. Glowsters or CommPass
family pagers must be off/out of the charger and not stacked to be
able to ‘hear’ this OTA programming change.
Out of Range
(OOR) ON/OFF
Scroll Down *
(OOR) ON/OFF
Scroll Down *
This feature is used to turn ON or OFF the out of range
transmissions at the transmitter. When OOR is active, the desktop
transmitter sends an OOR transmission every 7 seconds. If this
feature is active, a Glowster or CommPass pager will respond with
the appropriate OOR tone/voice response after missing more than
2 consecutive OOR transmissions. It is strongly recommended
that appropriate range testing be conducted in order to implement
the OOR feature properly.
transmissions at the transmitter. When OOR is active, the desktop
transmitter sends an OOR transmission every 7 seconds. If this
feature is active, a Glowster or CommPass pager will respond with
the appropriate OOR tone/voice response after missing more than
2 consecutive OOR transmissions. It is strongly recommended
that appropriate range testing be conducted in order to implement
the OOR feature properly.