Digital Security Controls Ltd. 05SKY User Manual

12

Select the type of default as follows:

• Entering 00 in sub-section [99]

1. A complete default of the system is performed
2. All reporting sub-sections, [30] through [78] are automat-

ically programmed as [FF] and will be sent by the Sky-
route transceiver.

• Entering 11 in sub-section [99]* 

1. A complete default is performed.
2. Reduced Reporting as follows:

1. Alarm Restoral Reporting Code, sub-sections [34]

through [38], will be automatically programmed to [00],
except the duress alarm.

2. The Keypad and PGM Restorals in section [39] will be

programmed to [00]. Zone Tamper & Restoral reporting
code, sub-sections [40] through [48], will be programmed
to [00]**.

3. Zone Supervisory & Restoral, sub-sections [49] through

[56], will be programmed to [00]**.

4. Zone Low Battery Alarm & Restoral, sub-sections [57]

through [64], will be programmed to [00]***.

5. Keypad Zone Restoral, sub-section [39], last 4 program-

ming locations, will be programmed as [00].

6. Miscellaneous Restoral and Periodic Test in sections [77]

and [78] will be programmed as [00].

In Generic mode, see Appendix A for Generic signals. (See
Section 3 ‘How Does It Work?’ for description of each report-
ing method). 

• Entering 12 in sub-section [99]*

1. A complete default is performed
2. Reduced Reporting as indicated above.

In Generic mode, see Appendix A for Generic signals. (See
Section 3 ‘How Does It Work?’ for description of each report-
ing method.) 

• Entering 03 in sub-section [99]

1. A complete default is performed.
2. All reporting sub-sections [30] to [78] are automatically pro-

grammed as [FF] and will be sent by the Skyroute Transceiver.

• Entering 13 in sub-section [99].

1. A complete default is performed.
2. The Skyroute will be programmed for backup mode.

All programming on the Skyroute transceiver is done in the
Installer Programming mode. Refer to the control panel’s
Installation Manual for instructions on how to enter Installer
Programming. From Installer Programming, enter section
[803] to go to the Skyroute programming sections. 

Sub-sections [01] to [22] apply to all other installations. 

Zone Definition: Sub-sections [01] to [05]

These sections must be programmed exactly the same as the
main control panel. This allows the Skyroute transceiver to
translate information sent along the Keybus and identify the
proper event. 

Configuration Options: Sub-section [06]
• Channel A enable/disable…………..option [1]

This option must be selected when the Cellemetry provider
is an “A” side carrier. 

• Channel B enable/disable…………..option[2]

This option must be selected when the Cellemetry provider
is a “B” side carrier.

• Home system only enable/disable…option[3]

This option must be programmed to ensure that the Skyroute
transceiver is communicating using the proper carrier. When
selected, the transceiver will only use towers with the same
SID (as programmed in section [07]). 

• To activate the Skyroute module in Home mode:

1. Select a channel, A or B, in address 06 (Option 1 or 2)
2. Wait for signal strength.
3. Enter in address 07 the Home SID number in hexadecimal

format.

4. Select Home mode (Option 3) and deactivate A or B chan-

nel in address 06.

Skyroute transceiver SID (System ID): 
Sub-section [07]
Please refer to the SID table included with the Skyroute mod-
ule to determine the SID number for your area.

Skyroute Test Time: Sub-section [10]
In this section enter the time of the day (24-hour format) you
want the test transmission to be sent.

Test Transmission Day Mask: Section [11]
In this section select the day of the week on which you want
the test transmission to be sent. 

* Any reporting code sub-section not mentioned is pro-

grammed as [FF].

** These signals only apply to installations with double EOL.

*** These signals only apply to installations with wireless zone

modules.