Digital Monitoring Products Inc PC0159 User Manual

23

You can specify any of the outputs/Favorites on the communicator to be activated by 

a zone condition. The output/Favorite can be activated regardless of the report to 

transmit or whether or not the zone is programmed as local. An output activated by a

non-24-hour armed zone is turned off when the zone’s area is disarmed by a user. To

enter an Output Number, press any Select key followed by the output number 1 or 2.

Press the COMMAND key.

Entering an Output Number displays this prompt that allows you to assign an output

action to the relay. A description of the available output actions is given below:

STEADY - The output is turned on and remains on until the area is disarmed, an output

cutoff time expires, or the output is reset from the keypad User Menu.

PULSE - The output alternates one second on and one second off until the area is

disarmed, an output cutoff time expires, or the output is reset from the keypad User

Menu.

MOMENTARY - The output is turned on only once for one second.

FOLLOW - The output is turned on and remains on while the zone is in an off normal, or

bad condition. When the zone restores, the output is turned off.

After you have selected the Message To Transmit, the display prompts you for the same

three selections for Disarmed Short, Armed Open, and Armed Short conditions. If the

zone is a 24-hour type, only the Armed Open and Armed Short conditions are displayed.

When you have programmed all of the zone conditions, the Swinger Bypass selection is

then  dis played.

Selecting YES allows the zone to be swinger bypassed by the communicator according to 

the programming in Swinger Bypass Trips and Reset Swinger Bypass. The Bypassed zone

displays in the keypad Status List. Selecting NO disables swinger bypassing for this zone.

If within one hour, a zone trips the total number of times as specified in Swinger Bypass

Trips, the communicator bypasses it until the following conditions occur; the area in

which the zone is assigned is disarmed, the zone is manually reset through the Bypass 

Zones keypad User Menu function, the zone remains normal for one hour and the Reset

Swinger Bypass is YES.

If the zone trips fewer than the specified times within one hour of the first trip, the

bypass trip counter returns to 0 (zero) and the process must be repeated.

A report of the swinger bypass is sent to the receiver if Bypass Reports is YES.

Select YES to enable cross-zoning for this zone. Cross-zoning requires this zone to trip

twice, or this zone and another cross-zoned zone to trip, within a programmed time 

before an alarm report is sent to the receiver. To operate correctly, all cross-zone zones 

need to be programmed as the same zone type.

When a cross-zoned zone trips, the Output action assigned to the zone activates. See

the Bell Action section. The cross-zone time specified in System Options begins to count

down. See the Cross-Zone Time section. If another cross-zoned zone in the system

faults, or if the first zone restores and faults again before the cross-zone time expires,

the bell turns on and the communicator sends an alarm report.

If no other cross-zone zone in the system trips before the cross-zone time expires, the 

communicator sends only a fault report from the first zone to the receiver.

Note: If CRS ZONE is YES, a valid CRS ZN TIME must be programmed for this feature to

be enabled.

This option displays if Zone Type is set for Auxiliary 1 or Auxiliary 2.

Press any top row key to select the Receiver Routing for the selected zone.

Select NORM to send Alarm and Supv/Trbl messages from this zone to receiver 1 or

receiver 2 as programmed within the receiver in Communications.

Select 1 to send Alarm and Supv/Trbl messages from this zone to receiver 1 only,

regardless of the programming for the receiver in Communications.

Select 2 to send Alarm and Supv/Trbl messages from this zone to receiver 2 only,

regardless of the programming for that receiver in Communications.

Select BOTH to send Alarm and Supv/Trbl messages from this zone to both receivers,

regardless of the programming for either receiver in Communications.

Enter the zone number you want to program next. Return to section 15.1 and follow

the descriptions of each programming prompt. If all zones are programmed, press the 

ARROW key at the ZONE NO: – display to continue.

ACTION:

STD  PLS  MOM FLW

SWGR BYP  NO  YES

CRS ZONE 

NO YES

RECEIVER  ROUTING

 

        NORMAL

NORM   1   2   BOTH  

ZONE NO: -