UTC Fire & Security Americas Corporation Inc 785B-ALGRO User Manual
8
Allegro
Preliminary 2/5/02
Devices (1st Tier)
(Default = none) Devices include a HW sensor, RF sensors,
RF touchpads, and other RF devices such as the DTIM.
RF touchpads, and other RF devices such as the DTIM.
Dial Dly
(Phones)
2nd Tier
(Default = 30 seconds, Parameters = 15-120 seconds) Dial
Delay determines how much time the user has to stop a panel
before it sends a false alarm to the central station.
Delay determines how much time the user has to stop a panel
before it sends a false alarm to the central station.
Alarm reports from sensors in groups 00–03, 10, and 13-20
can be aborted. To abort the dialing attempt, the user must
disarm the system within the Dial Dly time setting. Cancel and
restoral reports from these sensor groups are aborted at the
same time. The following reports can also be aborted.
can be aborted. To abort the dialing attempt, the user must
disarm the system within the Dial Dly time setting. Cancel and
restoral reports from these sensor groups are aborted at the
same time. The following reports can also be aborted.
❑
System Tamper Alarm/Cancel.
❑
Touchpad Police and Emergency Panic/Cancel.
❑
Forced Arming
❑
Recent Closing and Two Trip Error.
Note
Fire alarm reports to the central station cannot be aborted.
Fire alarm reports to the central station cannot be aborted.
To set the dial dly:
Enter the desired amount of time (15-120 seconds) and
then press #.
Pre-Dial String
(Phones)
2nd Tier
(Default = none, Parameters = 8 digits; 0-9, *, #, pause) This
feature lets you set up a dialing prefix to disable the call
waiting feature before the panel makes its first dialing attempt
to any programmed central monitoring station or downloader
phone number. The prefix can be up to eight digits. Contact
your local phone company for call waiting disable numbers
and characters. See Number 1 and 2 programming on page 7
for information on how to program * and # characters.
feature lets you set up a dialing prefix to disable the call
waiting feature before the panel makes its first dialing attempt
to any programmed central monitoring station or downloader
phone number. The prefix can be up to eight digits. Contact
your local phone company for call waiting disable numbers
and characters. See Number 1 and 2 programming on page 7
for information on how to program * and # characters.
Note
The pre-dial string is not accessible if a Dealer Code is pro-
grammed and the Installer Code is used to enter installer
programming mode. To access the pre-dial string option
when a Dealer Code is programmed, you must enter
installer programming mode using the Dealer Code.
The pre-dial string is not accessible if a Dealer Code is pro-
grammed and the Installer Code is used to enter installer
programming mode. To access the pre-dial string option
when a Dealer Code is programmed, you must enter
installer programming mode using the Dealer Code.
To set the pre-dial string:
Enter the desired numbers and then press #.
DTMF Dial
(Phones)
2nd Tier
(Default = on) This setting determines whether the panel uses
DTMF tones (on) or pulse (off) for dialing programmed phone
numbers.
DTMF tones (on) or pulse (off) for dialing programmed phone
numbers.
To turn DTMF dialing on or off:
Press # to turn it on or off.
Table 2: Sensor Group Assigned to Device
Device
Sensor Group
Keyfob or RF Touchpad
1
Portable Panic
1
HW Input
10
DWS
10
PIR
17
Sound
17
Glassguard
17
Smoke
26
Rate of Rise
26
DTIM
36
Table 3: Device Programming
Device
To Program
Door/Window Sensor (SAW) Press button on top of sensor
(cover removed).
Motion Sensor
Press button on back of sensor
(mounting plate removed).
(mounting plate removed).
Keychain Touchpad
(non encrypted)
(non encrypted)
Press lock & unlock buttons
until LED blinks.
until LED blinks.
Keychain Touchpad
(encrypted)
(encrypted)
See Note.
Crystal Sensors
See Note.
DTIM
3-2-1 sequence (on page 6).
Hardwire Sensor
For normally closed - separate
sensor from magnet.
sensor from magnet.
For normally opened - close
sensor then reopen.
sensor then reopen.
Note
When installing crystal sensors and encrypted keychain
touchpads, use the installation instructions included in
their packing boxes.
When installing crystal sensors and encrypted keychain
touchpads, use the installation instructions included in
their packing boxes.
Add
(Devices)
2nd Tier
(Default = none) When adding devices, the panel will
automatically assign the device to a sensor group based on the
type of device. Table 2 outlines the sensor group assigned to
each device.
automatically assign the device to a sensor group based on the
type of device. Table 2 outlines the sensor group assigned to
each device.
Note
To override the preassigned sensor number, use the arrow
keys to skip to the desired sensor number.
To override the preassigned sensor number, use the arrow
keys to skip to the desired sensor number.
To add a device:
1. Press
#
. The display shows
ZONE
{01- 20} -
TRIP
.
2. Trip the sensor (see Table 3). The panel beeps twice to indi-
cate the sensor was successfully learned into the panel.
3. Repeat step 2 until all desired zones are added.