Woodsonix Limited WSSB800TX User Manual
Figure 5. Probes and display unit opened for battery replacement
7. Care of the Unit
The SB800 is a sensitive piece of test equipment and should be treated with care.
Exposure to heat, moisture and dust should be avoided. If moisture is allowed to
enter the display unit or probes, the batteries should be removed and the units
thoroughly dried before reuse. The probe tips are especially sensitive to physical
shock. Do not tap or bang the probe tips sharply, as the internal transducer
ceramic is inherently brittle and may shatter. We recommend returning the unit
for service and calibration every year.
Exposure to heat, moisture and dust should be avoided. If moisture is allowed to
enter the display unit or probes, the batteries should be removed and the units
thoroughly dried before reuse. The probe tips are especially sensitive to physical
shock. Do not tap or bang the probe tips sharply, as the internal transducer
ceramic is inherently brittle and may shatter. We recommend returning the unit
for service and calibration every year.
8. Probe Operating Range
The probes are designed to work reliably up to 5 metres from the display unit.
Depending on environmental conditions, the necessary sensitivity of the display
unit's radio receiver may cause it to pick up signals from probes up to 200 metres
Depending on environmental conditions, the necessary sensitivity of the display
unit's radio receiver may cause it to pick up signals from probes up to 200 metres
away. This should be taken into consideration when simultaneous use is planned
for two SB800 units in the same vicinity.
for two SB800 units in the same vicinity.
9. Regulatory Conformance
The SB800 unit complies with AS/NZS 4268. It is approved for operation within
Australia and New Zealand.
The SB800U unit complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
It is approved for operation with within the United States.
NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR
MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY
RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID
THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
Australia and New Zealand.
The SB800U unit complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
It is approved for operation with within the United States.
NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR
MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY
RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID
THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
10. Disclaimer
All information provided in this document is carefully prepared and offered in
good faith as a guide to the operation of this product. System integrators must
ensure that the final system operates satisfactorily within the relevant regulatory
requirements and tolerances. We accept no responsibility for incorrect use or
unsafe employment of the resulting measurements. The suitability for any
particular purpose is not implied. We reserve the right to change products,
specifications, and installation data at any time, without notice.
good faith as a guide to the operation of this product. System integrators must
ensure that the final system operates satisfactorily within the relevant regulatory
requirements and tolerances. We accept no responsibility for incorrect use or
unsafe employment of the resulting measurements. The suitability for any
particular purpose is not implied. We reserve the right to change products,
specifications, and installation data at any time, without notice.
11. Warranty
This product is warranted for a period of 12 months from date of purchase against
faulty materials or workmanship. Your vendor will register your product with
Woodsonix.
Should any fault occur, the unit should be returned to your vendor. Any
unauthorised alterations, repairs, or opening of secured sections, will invalidate
the warranty. Warranty exclusions include, but are not limited to:
faulty materials or workmanship. Your vendor will register your product with
Woodsonix.
Should any fault occur, the unit should be returned to your vendor. Any
unauthorised alterations, repairs, or opening of secured sections, will invalidate
the warranty. Warranty exclusions include, but are not limited to: