Microchip Technology DM183037 Data Sheet
2012 Microchip Technology Inc.
DS30575A-page 541
PIC18F97J94 FAMILY
27.5.1
USB INTERRUPT STATUS
REGISTER (UIR)
REGISTER (UIR)
The USB Interrupt Status register (
) con-
tains the flag bits for each of the USB status interrupt
sources. Each of these sources has a corresponding
interrupt enable bit in the UIE register. All of the USB
status flags are ORed together to generate the USBIF
interrupt flag for the microcontroller’s interrupt funnel.
Once an interrupt bit has been set by the SIE, it must
be cleared in software by writing a ‘0’. The flag bits can
also be set in software, which can aid in firmware
debugging.
sources. Each of these sources has a corresponding
interrupt enable bit in the UIE register. All of the USB
status flags are ORed together to generate the USBIF
interrupt flag for the microcontroller’s interrupt funnel.
Once an interrupt bit has been set by the SIE, it must
be cleared in software by writing a ‘0’. The flag bits can
also be set in software, which can aid in firmware
debugging.
When the USB module is in the Low-Power Suspend
mode (UCON<1> = 1), the SIE does not get clocked.
When in this state, the SIE cannot process packets,
and therefore, cannot detect new interrupt conditions
other than the Activity Detect Interrupt, ACTVIF. The
ACTVIF bit is typically used by USB firmware to detect
when the microcontroller should bring the USB module
out of the Low-Power Suspend mode (UCON<1> = 0).
mode (UCON<1> = 1), the SIE does not get clocked.
When in this state, the SIE cannot process packets,
and therefore, cannot detect new interrupt conditions
other than the Activity Detect Interrupt, ACTVIF. The
ACTVIF bit is typically used by USB firmware to detect
when the microcontroller should bring the USB module
out of the Low-Power Suspend mode (UCON<1> = 0).
Register 27-7:
UIR: USB INTERRUPT STATUS REGISTER (ACCESS F62h)
U-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R-0
R/W-0
—
SOFIF
STALLIF
IDLEIF
(
)
TRNIF
(
ACTVIF
(
)
UERRIF
URSTIF
bit 7
bit 0
Legend:
R = Readable bit
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7
Unimplemented: Read as ‘0’
bit 6
SOFIF: Start-of-Frame Token Interrupt bit
1 = A Start-of-Frame token is received by the SIE
0 = No Start-of-Frame token is received by the SIE
1 = A Start-of-Frame token is received by the SIE
0 = No Start-of-Frame token is received by the SIE
bit 5
STALLIF: A STALL Handshake Interrupt bit
1 = A STALL handshake was sent by the SIE
0 = A STALL handshake has not been sent
1 = A STALL handshake was sent by the SIE
0 = A STALL handshake has not been sent
bit 4
IDLEIF: Idle Detect Interrupt bit
)
1 = Idle condition is detected (constant Idle state of 3 ms or more)
0 = No Idle condition is detected
0 = No Idle condition is detected
bit 3
TRNIF: Transaction Complete Interrupt bit
(
)
1 = Processing of pending transaction is complete; read the USTAT register for endpoint information
0 = Processing of pending transaction is not complete or no transaction is pending
0 = Processing of pending transaction is not complete or no transaction is pending
bit 2
ACTVIF: Bus Activity Detect Interrupt bit
)
1 = Activity on the D+/D- lines was detected
0 = No activity detected on the D+/D- lines
0 = No activity detected on the D+/D- lines
bit 1
UERRIF: USB Error Condition Interrupt bit
)
1 = An unmasked error condition has occurred
0 = No unmasked error condition has occurred.
0 = No unmasked error condition has occurred.
bit 0
URSTIF: USB Reset Interrupt bit
1 = Valid USB Reset occurred; 00h is loaded into the UADDR register
0 = No USB Reset has occurred
1 = Valid USB Reset occurred; 00h is loaded into the UADDR register
0 = No USB Reset has occurred
Note 1:
Once an Idle state is detected, the user may want to place the USB module in Suspend mode.
2:
Clearing this bit will cause the USTAT FIFO to advance (valid only for IN, OUT and SETUP tokens).
3:
This bit is typically unmasked only following the detection of a UIDLE interrupt event.
4:
Only error conditions enabled through the UEIE register will set this bit. This bit is a status bit only and
cannot be set or cleared by the user.
cannot be set or cleared by the user.