Bosch AXT 25 TC 0 600 803 300 Data Sheet
Product codes
0 600 803 300
F 016 L70 735 | (11.4.11)
Bosch Power Tools
16 | English
Adjustment of the pressure plate 15 is neces-
sary as a result of wear (shredded material,
e. g. branches, hangs together as a chain and
is not properly cut through).
With the motor running in the forward direc-
tion (green button 4), turn the adjustment
knob 10 a small amount at a time in a clock
wise direction until a light grinding sound can
be heard (the cutting roller 16 cuts the pres-
sure plate 15 to the proper clearance, and
some small aluminium shavings fall out of the
ejection chute).
sary as a result of wear (shredded material,
e. g. branches, hangs together as a chain and
is not properly cut through).
With the motor running in the forward direc-
tion (green button 4), turn the adjustment
knob 10 a small amount at a time in a clock
wise direction until a light grinding sound can
be heard (the cutting roller 16 cuts the pres-
sure plate 15 to the proper clearance, and
some small aluminium shavings fall out of the
ejection chute).
To check, look for shavings in the collection
box 11.
Readjust only to the required extent, other-
wise the pressure plate 15 could wear unnec-
essarily.
box 11.
Readjust only to the required extent, other-
wise the pressure plate 15 could wear unnec-
essarily.
Troubleshooting
The following chart lists problem symptoms, possible causes and corrective action, if your gar-
den product does not operate properly. If these do not identify and correct the problem, con-
tact your service agent.
f
den product does not operate properly. If these do not identify and correct the problem, con-
tact your service agent.
f
Warning! Switch off, remove plug from mains before adjusting, cleaning or if cable is cut,
damaged or entangled.
damaged or entangled.
Maintenance and Service
Maintenance and Cleaning
f
Warning! Switch off, remove plug from
mains before adjusting, cleaning or if ca-
ble is cut, damaged or entangled.
mains before adjusting, cleaning or if ca-
ble is cut, damaged or entangled.
f
Always wear protective gloves when us-
ing, adjusting or cleaning the garden
product.
ing, adjusting or cleaning the garden
product.
Note: To ensure long and reliable service, car-
ry out the following maintenance regularly.
ry out the following maintenance regularly.
Regularly check for obvious defects such as
loose, dislodged or damaged blades, loose
fixings, and worn or damaged components.
Check that covers and guards are undamaged
and correctly fitted. Carry out necessary
maintenance or repairs before using.
If the garden product should happen to fail
despite the care taken in manufacture and
testing, repair should be carried out by an au-
thorised customer service agent for Bosch
garden products.
loose, dislodged or damaged blades, loose
fixings, and worn or damaged components.
Check that covers and guards are undamaged
and correctly fitted. Carry out necessary
maintenance or repairs before using.
If the garden product should happen to fail
despite the care taken in manufacture and
testing, repair should be carried out by an au-
thorised customer service agent for Bosch
garden products.
Problem
Possible Cause
Corrective Action
Garden product
fails to operate
fails to operate
Collection box not fitted correctly
Fit collection box correctly
Chute assembly not fitted correctly Fit chute assembly correctly
Mains socket faulty
Mains socket faulty
Use another socket
Extension cable damaged
Inspect cable, replace if damaged
Fuse faulty/blown
Replace fuse
Machine beeps (al-
so two lights on
AXT 23 TC/25 TC)
and does not start
so two lights on
AXT 23 TC/25 TC)
and does not start
Collection box/chute is not correct-
ly assembled
ly assembled
Ensure the collection box is in posi-
tion
Ensure the chute assembly is in po-
sition and clamped by turning the
clamping knob (red) fully clockwise
tion
Ensure the chute assembly is in po-
sition and clamped by turning the
clamping knob (red) fully clockwise
One flashing light
on
AXT 23 TC/25 TC
on
AXT 23 TC/25 TC
None, this is ok, machine is “pluged
in” and ready to use
in” and ready to use
The material to be
shredded is not
pulled in
shredded is not
pulled in
Material to be shredded is wet and
soft
soft
Use the prodder to push the mate-
rial into the machine
rial into the machine
Jammed material in the machine
Clear jammed material (always
wear gardening gloves)
Use the reverse button (see “Re-
turn Motion”)
wear gardening gloves)
Use the reverse button (see “Re-
turn Motion”)
Shredded material
is not completely
separated and
hangs together as
a chain
is not completely
separated and
hangs together as
a chain
Pressure plate requires adjustment see “Pressure Plate Adjustment
(see figure H)”
The material
stucked between
the cutter and
pressure plate and
can not be re-
leased by the re-
verse button
stucked between
the cutter and
pressure plate and
can not be re-
leased by the re-
verse button
Pressure plate were over set
Push in adjusting knob 10 and in-
sert Allen key 17 (sized 5 – not in-
cluded) into the recess on the end
of adjusting screw and release by
anti clockwise (see figure I)
Then repeat pressure plate
adjustment (see “Pressure Plate
Adjustment (see figure H)”)
sert Allen key 17 (sized 5 – not in-
cluded) into the recess on the end
of adjusting screw and release by
anti clockwise (see figure I)
Then repeat pressure plate
adjustment (see “Pressure Plate
Adjustment (see figure H)”)
OBJ_BUCH-895-003.book Page 16 Monday, April 11, 2011 1:52 PM