Graupner Hendheld RC 2.4 GHz No. of channels: 12 33124 Data Sheet
Product codes
33124
134 Detail program description - Control adjust
Phase assignment
Setting up fl ight phases
Using the arrow keys on the left or right touch pad, page
to the menu option "Phase assignment" in the multi-
function list:
to the menu option "Phase assignment" in the multi-
function list:
Phase settings
Phase trim
Control switch
Timers (general)
Non-delayed chan
Phase assignment
Fl. phase timers
Phase settings
Control switch
Timers (general)
Non-delayed chan
Phase assignment
Tap the center
SET
key on the right touch pad to open
the menu shown below:
PHASE ASSIGNMENT
prior.
A B
A B
C D E F
1
nor mal
combi
Note:
A phase name appears to the right of the phase number
at the bottom right of the display only if you have
assigned the name beforehand on the "Phase settings"
menu.
A phase name appears to the right of the phase number
at the bottom right of the display only if you have
assigned the name beforehand on the "Phase settings"
menu.
On the "Phase settings" menu – described above
separately for fi xed-wing and helicopter models – you
separately for fi xed-wing and helicopter models – you
will have set up names for your phases. On this menu –
which is identical for both model types – you must now
specify the switches or switch combinations that you
want to use to trigger each phase. One exception for heli
menu: one of the two auto-rotation switches must be set
on the menu "Base setup model".
which is identical for both model types – you must now
specify the switches or switch combinations that you
want to use to trigger each phase. One exception for heli
menu: one of the two auto-rotation switches must be set
on the menu "Base setup model".
Please note the following priorities:
If you have not yet assigned
•
any fl ight phase
switches to any phase names, you will always fi nd
yourself in fl ight phase "1". Accordingly, by the time
you start programming fl ight phases, you should
therefore have already given this fl ight phase the
phase name "Normal".
Independently of the switch positions of phases
yourself in fl ight phase "1". Accordingly, by the time
you start programming fl ight phases, you should
therefore have already given this fl ight phase the
phase name "Normal".
Independently of the switch positions of phases
•
assigned to switches using this menu, the auto-
rotation phase – applicable only to the "Helicopter"
model type and whose switch is assigned on the
"Base setup model" menu – always (!) takes
precedence. Accordingly, as soon as the auto-
rotation switch in question is activated, the following
warning appears:
rotation phase – applicable only to the "Helicopter"
model type and whose switch is assigned on the
"Base setup model" menu – always (!) takes
precedence. Accordingly, as soon as the auto-
rotation switch in question is activated, the following
warning appears:
A B
C D E F
1
nor mal
PHASE ASSIGNMENT
prior.
combi
Autorot
Phase switch "A" is given priority over all subsequent
•
switch positions, from "B" to "F"
Phase switch "B" is given priority over all subsequent
Phase switch "B" is given priority over all subsequent
•
switch positions, from "C" to "F"
The two 3-stage switches, SW 4/5 and 6/7, should
The two 3-stage switches, SW 4/5 and 6/7, should
•
always be assigned from the center point position.
For this reason, use switch "A" and/or switch "B" only if
you wish to change from any other fl ight phase – apart
from the heli's auto-rotation phase – directly into the
phase that is assigned to this switch.
you wish to change from any other fl ight phase – apart
from the heli's auto-rotation phase – directly into the
phase that is assigned to this switch.
Programming fl ight phase switches
Once you have confi gured your desired switch position,
"A" to "F", using the arrow keys on the left or right
touch pad, a switch (whether a "normal" switch or an
expanded switch) is then assigned as described in the
section "Assigning transmitter controls, switches and
control switches" (page 52).
"A" to "F", using the arrow keys on the left or right
touch pad, a switch (whether a "normal" switch or an
expanded switch) is then assigned as described in the
section "Assigning transmitter controls, switches and
control switches" (page 52).
The order in which assignment is made is irrelevant:
•
you must ensure only that you assign what are, for
you, the "correct" switches. (In the heli program, for
example, you should also take care to ensure you do
not use this menu to re-assign any auto-rotation switch
already assigned on the " Base setup model" menu.)
you, the "correct" switches. (In the heli program, for
example, you should also take care to ensure you do
not use this menu to re-assign any auto-rotation switch
already assigned on the " Base setup model" menu.)
Example: 4 fl ight phases with phase priority
A B
C D E F
1 Nor mal
2
6
7
PHASE ASSIGNMENT
prior.
combi
Assigning fl ight phases to switch positions
You have now assigned names to the fl ight phases (1
… max. 7) on the "Phase settings" menu and also
programmed switches on this menu, but … at the bottom
right of the display screen, you only see "<1 normal >" –
regardless of the positions the switches are in!?
… max. 7) on the "Phase settings" menu and also
programmed switches on this menu, but … at the bottom
right of the display screen, you only see "<1 normal >" –
regardless of the positions the switches are in!?