Graupner Hendheld RC 2.4 GHz No. of channels: 12 33124 Data Sheet
Product codes
33124
135
Detail program description - Control adjust
Use the arrow keys on the left or right touch pad to
move the marker frame down and to the right and then
briefl y tap the center
move the marker frame down and to the right and then
briefl y tap the center
SET
key on the right touch pad:
A B
C D E F
2
6
7
1 Nor mal
PHASE ASSIGNMENT
prior.
combi
Now close one (or more, as required) of the switches
that you have assigned, and assign one of the fl ight
phase names from the list you selected beforehand on
the "Phase settings" menu to this switch position or
combination.
Here, for example, we assign the "Launch" phase to the
closed ("I") priority switch "A" …
that you have assigned, and assign one of the fl ight
phase names from the list you selected beforehand on
the "Phase settings" menu to this switch position or
combination.
Here, for example, we assign the "Launch" phase to the
closed ("I") priority switch "A" …
A B
C D E F
2
6
7
2 Launch
PHASE ASSIGNMENT
prior.
combi
… if, for example, we wish to switch to this phase
regardless of the "C" … "F" switch positions, because
the same switch activates an electric motor, etc.
Use the same approach to set the other switches or
combinations of switches.
Theoretically – for the situation where all three are
closed – you could use the three single switches shown
in the example to defi ne an additional fi fth fl ight phase
on the "Phase settings" menu. However, since this
example assumes just four fl ight phases, you can leave
regardless of the "C" … "F" switch positions, because
the same switch activates an electric motor, etc.
Use the same approach to set the other switches or
combinations of switches.
Theoretically – for the situation where all three are
closed – you could use the three single switches shown
in the example to defi ne an additional fi fth fl ight phase
on the "Phase settings" menu. However, since this
example assumes just four fl ight phases, you can leave
the default phase name as "1 Normal" for this switch
position.
You can leave this menu in the familiar way by pressing
the center
position.
You can leave this menu in the familiar way by pressing
the center
ESC
key on the left touch pad.
Tips:
If you have named more phases than you currently
•
have switches defi ned for then this is not really
problematic. You can repeat and change your switch
assignment as you wish at any point in time. And you
can also name additional phases at any time and
then assign switches to them.
When assigning switches, check whether the
problematic. You can repeat and change your switch
assignment as you wish at any point in time. And you
can also name additional phases at any time and
then assign switches to them.
When assigning switches, check whether the
•
switches are already otherwise assigned to ensure
that you avoid duplicate assignments.
that you avoid duplicate assignments.
Important notice:
Before a phase switch is assigned, the model
settings confi gured are now to be found in the fl ight
phase "1 Normal", i. e. all fl ight phase-dependent
menus are reset to the standard confi gurations for
all other fl ight phases.
Before a phase switch is assigned, the model
settings confi gured are now to be found in the fl ight
phase "1 Normal", i. e. all fl ight phase-dependent
menus are reset to the standard confi gurations for
all other fl ight phases.
To avoid having to start from scratch in every fl ight
phase, you can copy over these standard settings
by using the command "Copy fl ight phase" on the
"Copy / Erase" menu to replace them with fl ight
data obtained from the "Normal" fl ight phase. You
then need only to make further fl ight phase-specifi c
changes to the settings.
phase, you can copy over these standard settings
by using the command "Copy fl ight phase" on the
"Copy / Erase" menu to replace them with fl ight
data obtained from the "Normal" fl ight phase. You
then need only to make further fl ight phase-specifi c
changes to the settings.