Graupner Hendheld RC 2.4 GHz No. of channels: 12 33124 Data Sheet
Product codes
33124
253
Detail program description - Control adjust
point at the selected position by briefl y pressing the
central
central
SET
key of the right touch pad. The switch status
is shown to the right of the control number:
SEL
0%
0%
0%
0%
0%
C1
C2
C3
C2
C3
–––
C4
CONTROL SWITCH
–85%
STO
–––
–––
–––
Ct6
Notice:
Now place the switching point; but do not put it at the
limit position of the control, because safe switching is
not assured when doing so.
Now place the switching point; but do not put it at the
limit position of the control, because safe switching is
not assured when doing so.
Ct1 used in the example here should be "closed" in the
"full throttle" direction and "open" below the switching
point.
Now switch to the menu ...
"full throttle" direction and "open" below the switching
point.
Now switch to the menu ...
""Timers (gen.)" (page138 … 141)
…, and, with the arrow keys, select the line "Top", to
which the "Tim(ers)" are assigned by standard. In this
line, move the marking frame over the "Timer" column to
the right, to the column above the switch symbol, using
the appropriate arrow key of the left or right touch pad.
Now press the central
which the "Tim(ers)" are assigned by standard. In this
line, move the marking frame over the "Timer" column to
the right, to the column above the switch symbol, using
the appropriate arrow key of the left or right touch pad.
Now press the central
SET
key of the right touch pad
twice: Pressing once activates the switch assignment
and tapping again opens the list of the "expanded
switches":
and tapping again opens the list of the "expanded
switches":
Model time
Akkuzeit
Oben:
Mitte: Flug
Akkuzeit
Oben:
Mitte: Flug
Alar m
–––
0:34h
1:23h
1:23h
0s
0s
0s
Stopp
–––
–––
–––
SEL
Control/fix sw
C1
C2 C3 C4 FX
FXi C1i C2i C3i C4i
Now select the previously programmed control switch
"Ct1" and then press the central
"Ct1" and then press the central
SET
key of the right
touch pad.
Model time
Batt. time
Top :
Centr : Flight
Batt. time
Top :
Centr : Flight
Alar m
–––
0:34h
1:23h
1:23h
0s
0s
0s
Stop
C1
–––
–––
SEL
The timer in the base screen now starts with movement
of the proportional rotary control toward full throttle and
stops if you pull it back over the switching point.
of the proportional rotary control toward full throttle and
stops if you pull it back over the switching point.
Examples 2 and 3 of the preceding pages
If you control your motor with a switch, on the other
hand, you do not need the described control switch
described above. It is completely suffi cient if you assign
the same switch to the timer, so that it also begins to run
when you switch on the motor.
If you control your motor with a switch, on the other
hand, you do not need the described control switch
described above. It is completely suffi cient if you assign
the same switch to the timer, so that it also begins to run
when you switch on the motor.
Tip:
If the motor run time for an E-model is limited by the
battery capacity, you can have the stopwatch count
down. Enter the maximum permissible motor run time
in the "Timer" column, e.g. "5 min", and briefl y before
the expiration of the permissible time, e. g. "30 s" before,
have the transmitter issue an acoustic warning signal:
If the motor run time for an E-model is limited by the
battery capacity, you can have the stopwatch count
down. Enter the maximum permissible motor run time
in the "Timer" column, e.g. "5 min", and briefl y before
the expiration of the permissible time, e. g. "30 s" before,
have the transmitter issue an acoustic warning signal:
Model time
Batt. time
Top :
Centr : Flight
Batt. time
Top :
Centr : Flight
Timer
–––
12:34h
1:23h
0:00
Stop
5
:00
Model time
Batt. time
Top :
Centr : Flight
Batt. time
Top :
Centr : Flight
Alar m
–––
0:34h
1:23h
1:23h
0s
Stop
C3
–––
–––
SEL
30s