Graupner Hendheld RC 2.4 GHz No. of channels: 12 33124 Data Sheet
Product codes
33124
255
Detail program description - Control adjust
Tail type
Motor at C1
None
Aile/flaps
1AIL
M O D E L T Y P E
Brake Off
In 1
+100%
SEL
2ELSv3+8
Then carry out the fi ne-tuning of the travel of the two
servos "as accustomed" in the "Servo adjustment"
menu.
servos "as accustomed" in the "Servo adjustment"
menu.
Two rudders
We want to switch two rudders "in parallel". The second
rudder is located at the free receiver output 8.
Variant 1
In the menu …
We want to switch two rudders "in parallel". The second
rudder is located at the free receiver output 8.
Variant 1
In the menu …
"Cross-mixer"
(page 194)
… select one of the cross-mixers and enter "8" and "RU"
in its left and center value fi elds, as shown in the fi gure:
in its left and center value fi elds, as shown in the fi gure:
Typ
Diff.
zu
DUAL MIXER
Mixer1
Mixer2
Mixer2
8
Mixer3
Mixer4
Mixer4
??
??
??
??
??
??
0%
0%
0%
0%
0%
0%
0%
RU
The same defl ection "
", which would take place
through "Input 8" may not have an effect here. Therefore,
you should make absolutely sure in the …
you should make absolutely sure in the …
"Control adjust"
menu (page 96)
Input 5
offset
0%
0%
0%
0%
0%
–––
0%
Input 6
Input 7
Input 8
Input 7
Input 8
–––
–––
GL
GL
GL
GL
typ
nor mal
–––
… that "Input 8" is set to "free" so that the control
function is separate from the control channel.
Alternatively, You can set Input 8 in the "Only mix
channel" to "no control", regardless of the fl ight phase,
by setting Channel 8 to "only mix":
function is separate from the control channel.
Alternatively, You can set Input 8 in the "Only mix
channel" to "no control", regardless of the fl ight phase,
by setting Channel 8 to "only mix":
MIX ONLY CHANNEL
only
nor mal
nor mal
7 8 9 10 11 12
Variant 2
With this variant a mixer, "Tr Rudd 8" should be set in
the menu …
With this variant a mixer, "Tr Rudd 8" should be set in
the menu …
" Free mixers "
(page 181)
. In the "Type" column, select the setting "Tr" so that
the rudder trimming affects both rudder servos:
the rudder trimming affects both rudder servos:
ty
fr
to
M1
M2
M3
M2
M3
RU
8
??
??
M4
M5
M5
??
??
??
??
??
??
Tr
Then switch to the graphic screen and set a symmetric
mixture of +100%.
mixture of +100%.
L.MIX 1
0%
Offset
ASY
SYM
RU
8
Mix input
+100% +100%
"Input 8" should also be programmed to "free" here in
the "Control adjust" - in all fl ight phases, if applicable.
However, control function "8" can be separated from
control channel "8" more easily in the fl ight-phase
independent menu "Only mix channel", page 193:
the "Control adjust" - in all fl ight phases, if applicable.
However, control function "8" can be separated from
control channel "8" more easily in the fl ight-phase
independent menu "Only mix channel", page 193:
MIX ONLY CHANNEL
only
nor mal
nor mal
7 8 9 10 11 12