Boss Audio Systems GT-10B User Manual

 

▼

 

▲

 

The Number pedal and the BANK pedal are used for 
switching specified effects on and off.

 

Off

The function is not assign to the pedals.

Ch.A/B

Switches between effect channel A and B.

Comp

Switches the COMP on and off.

OD/DS

Switches the OD/DS on and off.

Preamp

Switches the PREAMP/SPEAKER on and off.

EQ

Switches the EQ on and off.

FX1

Switches the FX-1 on and off.

FX2

Switches the FX-2 on and off.

Delay

Switches the DELAY on and off.

Chorus

Switches the CHORUS on and off.

Reverb

Switches the REVERB on and off.

PdlFX

Switches the PEDAL FX on and off.

S/R

Switches the SEND/RETURN on and off.

AmpCtl

Switches the Amp Control on and off.

Tuner

Switches the TUNER on and off.

PL

Switches the PHRASE LOOP on and off.

PL R/P

Records/plays back the phrase.

PL Clr

Clears the phrase.

PL M/P

Mutes playback of the phrase.

BPMTap

Used for tap input of the Master BPM.

DlyTap

Used for tap input of the delay time.

MIDI

Controls the Start/Stop of external MIDI devic-
es (such as sequencers).

MMCPly

Controls the Play/Stop of external MIDI devic-
es (such as hard disk recorders).

Lev+10

Increases the patch volume level by 10 units.

Lev+20

Increases the patch volume level by 20 units.

Lev-10

Decreases the patch volume level by 10 units.

Lev-20

Decreases the patch volume level by 20 units.

NumInc

Switches to the next higher patch number in the 
same bank as the currently selected patch.

NumDec

Switches to the next lower patch number in the 
same bank as the currently selected patch.

BnkInc

Switches to the next higher bank number.

BnkDec

Switches to the next lower bank number.

 

Patch

The patch preamp setting is used. This allows you to 
use different preamp settings in each individual patch.

System1–3

The system’s preamp setting is used. This applies 
the same preamp settings to all patches.

 

Pressing EZ TONE [CREATE] automatically switches 
Preamp Mode to Patch.

 

This setting determines whether or not the decay of reverb, delay, and 
similar effects continue when patches are switched on the GT-10B.

Fast

Patches are changed normally. The unit switches to 
the subsequent patch without any carry-over of the 
decay from the previous patch’s reverb or delay.

Smooth

The unit switches to the subsequent patch with the 
decay from the previous patch’s reverb or delay 
continued after the switch is made.

 

To ensure smooth switching, the patches may be switched 
with a delay of one tempo beat.

 

This sets the timing with which the GT-10B switches to the next 
patch when switching banks with the pedals.

Wait

Although the indication in the display is updated to 
reflect the change in the bank when a BANK pedal 
is pressed, the patch will not change until a number 
pedal has been pressed.

Immed

The patch switches instantly when a BANK pedal 
or any of the number pedals is pressed.

 

P01–P50, 
U01–U50

Sets the lower limit for the banks.

 

P01–P50, 
U01–U50

Sets the upper limit for the banks.

 

This setting determines whether or not the Assign’s (p. 51) opera-
tional status is carried over to the next patch when patches are 
switched.

Off

The Assign’s operational status is not carried over.
(Example)
If a patch is switched while the volume is being con-
trolled with an EXP Pedal, the volume of the subse-
quent patch is set to the value set in that patch.
If the EXP Pedal is operated, the volume will 
change in accord with the pedal’s movement.

On

The Assign’s operational status is carried over.
(Example)
If a patch is switched while the volume is being con-
trolled with the EXP Pedal, the volume of the sub-
sequent patch will take on the value determined by 
the current pedal position (angle). If the patch 
switched to has the EXP Pedal controlling the wah 
effect, then the volume assumes the value set in the 
patch, and the patch’s wah effect is given the value 
derived from the current pedal position (angle).

GT-10B_e.book 136 ページ ２００８年２月２６日　火曜日　午後３時３０分