Vortech Engineering Nissan 350Z/Infinity G35Supercharger System 2003-2006 User Manual
P/N: 4NZ020-010
©2007 Vortech Engineering, LLC
All Rights Reserved, Intl. Copr. Secured
12JAN07 v4.0 Nissan 350Z(4NZv4.0)
8
6.
SUPERCHARGER MOUNTING PLATE INSTALLATION (2005 and Later
“Rev-Up” Engines)
“Rev-Up” Engines)
NOTE:
Oil in the supercharger is gravity drained
to the oil pan. Trim the supplied oil drain
hose as necessary so that it is continu-
ously sloping down towards the oil pan.
Avoid dips, kinks, etc.
A.
Remove the wire loom push pins and re-route
the wires around the outside (driver’s side) of
the sheet metal bracket. (See Fig. 6-a.)
the wires around the outside (driver’s side) of
the sheet metal bracket. (See Fig. 6-a.)
B.
Install the supplied Ø1/2" fabric-braid oil drain
line onto the supercharger fitting and tighten
the supplied hose clamp.
line onto the supercharger fitting and tighten
the supplied hose clamp.
C.
Install the supplied 1/8"NPT x -4 straight fitting
into the supercharger oil feed nozzle using
motor oil on the threads. Attach the supplied
oil feed hose to the fitting and tighten.
into the supercharger oil feed nozzle using
motor oil on the threads. Attach the supplied
oil feed hose to the fitting and tighten.
NOTE:
Use clean oil on the pipe (tapered)
threads. Teflon tape or sealant is not rec-
ommended as it may loosen and cause
blockage of the small oil feed orifice
resulting in supercharger failure.
Fig. 6-b
Fig. 6-a
Fig. 6-c
Fig. 6-d
D.
Install the mounting plate to engine screws
through through the mounting plate in the
position shown in Fig. 6-b. These screws
must be installed first because once the
supercharger is mounted, some of them can
not be installed.
through through the mounting plate in the
position shown in Fig. 6-b. These screws
must be installed first because once the
supercharger is mounted, some of them can
not be installed.
E.
Install the supplied 6-rib belt around the 6-rib
aluminum pulley on the mounting bracket
assembly. Install the supercharger onto the
mounting plate with the supplied .53" spacers
(see Fig. 6-c) between the supercharger and
the mounting plate. Secure with the four 3/8"
x 1-3/4" bolts.
aluminum pulley on the mounting bracket
assembly. Install the supercharger onto the
mounting plate with the supplied .53" spacers
(see Fig. 6-c) between the supercharger and
the mounting plate. Secure with the four 3/8"
x 1-3/4" bolts.
F.
Install the supplied gilmer (toothed) belt
around the pulleys on the mounting plate
assembly.
around the pulleys on the mounting plate
assembly.
G.
Install the three various mounting plate spac-
ers onto their respective screws. (See Fig.
6-b.) A small dab of sealant between the
spacer and the mounting plate may help
retain them during installation.
ers onto their respective screws. (See Fig.
6-b.) A small dab of sealant between the
spacer and the mounting plate may help
retain them during installation.
H.
Position the supercharger mounting plate
assembly in front of the engine and start all
of the mounting screws. (See Fig. 6-d.)
assembly in front of the engine and start all
of the mounting screws. (See Fig. 6-d.)
I.
Make sure that the coolant hose is routed in
front of the supercharger mounting plate.
front of the supercharger mounting plate.
J.
Verify that the oil drain hose is routed as
smoothly as possible and connect it to the fit-
ting on the oil pan. Tighten a hose clamp on
this connection. Secure the oil drain hose and
the A/C line away from the A/C pulley with
zip-ties. Trim the drain hose length if
necessary.
smoothly as possible and connect it to the fit-
ting on the oil pan. Tighten a hose clamp on
this connection. Secure the oil drain hose and
the A/C line away from the A/C pulley with
zip-ties. Trim the drain hose length if
necessary.
M6 x 20mm
M12 x 110mm
M6 x 70mm
Ø.5" x 1.175"
SPACERS
Ø1" x .602"
SPACER
SPACER