Bosch Appliances Home Security System D9412GV2 User Manual

D9412GV2/D7412GV2 | Operation and Installation Guide | 14.0 Faceplates

Bosch Security Systems, Inc. | 5/05 | F01U003641B

14.0 Faceplates

14.1 D9412GV2

Faceplate

Figure 32: D9412GV2 Faceplate

EARTH GROUND

COMMON

BATTERY NEGATIVE ONLY

BATTERY POSITIVE ONLY

RELAY A

RELAY B

RELAY C

+ AUX POWER

CLASS 2 TRANSFORMER
16.5 VAC 40 VA 60 Hz
Model D1640
Internally Fused - Do not short
Requires Unswitched Outlet
Do not share with other equipment

GROUND FAULT DETECT

Enabled
Disabled

PHONE
LED

RED

ON when
communicating
OFF when idle

Digital Alarm Communicator Transmitter

D9412GV2 Control/Communicator is UL Listed For Central Station, Local, Remote Station and
Household Fire Alarm, and Central Station, Local, Police Station Connect, Household Burglar Alarm
and Encrypted Line Security when communicating via a network.

System is intended to be checked by a Qualified Technician at least every 3 years.

The types of initiating circuits the panel has been approved for are A, M, W, SS.

VOLTAGE RANGES

Open

3.7 - 5.0 VDC

Normal

2.0 - 3.0 VDC

Short

0.0 - 1.3 VDC

Reset Pin

Disable all except Battery

Charging and Programming

PERIPHERAL DEVICE CONNECTIONS

RED

POWER +

YELLOW

DATA BUS A

GREEN

DATA BUS B

BLACK

COMMON

ZONEX OUT 1

ZONEX IN 1

N.F.P.A.
Style 3.5
Signaling
Line
Circuits

F01U003643B

Point 1 Point 2

Point 3 Point 4

Point 5 Point 6

Point 7 Point 8

LEDs Off When Normal

Charging Status

Low Battery - 12.1 VDC

YEL

RED

10.2 VDC - Battery Load Shed

This equipment should be installed in accordance with the NFPA 70 (National Electrical Code)
and NFPA 72 (National Fire Alarm Code) for Local, Central Station, Remote Station, Proprietary and
Household Fire Warning Systems and under the limits of the Local Authority Having Jurisdiction
(National Fire Protection Association, Battermarch Park, Quincy, MA 02269). Printed information
describing proper installation, operation, testing, maintenance, evacuation planning and repair
service is to be provided with this equipment.

D9412GV2

ZONEX POWER +

ZONEX COMMON

PHONE LINE SEIZED

TIP

RING

TELCO CORD
MODEL D161

SDI Connector

ZONEX OUT 2

ZONEX IN 2

Refer to D9412GV2/D7412GV2 Approved Applications Compliance Guide (P/N: F01U003639___)

For System Wiring Diagram, Issue A

Refer to D9412GV2/D7412GV2 Approved Applications Compliance Guide (P/N: F01U003639___)

For Compatible Smoke Detectors

POWER SUPPLY REQUIREMENTS

The Power Supply provides a maximum of 1.4 Amps for the Control Panel and all
Accessory Devices. For System Loading, refer to D9412GV2/D7412GV2
Operation and Installation Guide (P/N: F01U003641___).

(P/N: F01U003641) for Power Requirements relating to Terminals 6 and 7 .

CAUTION:

See D9412GV2/D7412GV2 Operation and Installation Guide

All external connections except Terminal 5 (battery positive) are inherently power
limited. Requirements for battery standby time might reduce allowable output.

WARNING!

Multi-Battery installation requires
Model D122/D122L Dual Battery
Harness. Improper installation can
be a fire hazard.

Battery: Replace every 3 to
5 years with one or two Model
D126 12V 7Ah or D1218
12V 18Ah Lead Acid Batteries.

GRN

D5200/D5360
PROG CONN

Point 8
S3 Option

Closed = 1K

EOL

Normal Operation

Open =AB-12 UL
Bell Box 220 K

CAUTION:

Avoid damage to Panel.

Do not connect 24 V to terminals.

Maximum charging current 1.4 A

PROGRAMMABLE
ALARM OUTPUTS

Terminals

SWITCHED AUX

and

Terminal

TELCO

RING

TIP

PHONE LINE
SEIZED

1 - Charging status LED (yellow)

2 - Low battery LED (red)

3 - Color-coded battery leads

4 - Ground fault detect enable

Phone LED (red)

6 - Telephone cord connector

Point 8 ground fault detect enable/disable

Operation monitor LED (green)

9- Accessory

connector

10- Programming connector

11- Reset pin