Bosch Appliances Home Security System CC880 User Manual
CC880/LP880, SC8016 | Operators Guide | 23.0
Remote Arming By Telephone
EN | 15
Bosch Security Systems | 6/04 | 920036O.OG.162
Example
If the AREA DISPLAY displays number 2, all
operations performed only operate Area 2. To
operate Area 1, you need to press the [#] key until
the AREA DISPLAY displays number 1. Pressing
the [#] button again toggles you back to the Area 2
display.
operations performed only operate Area 2. To
operate Area 1, you need to press the [#] key until
the AREA DISPLAY displays number 1. Pressing
the [#] button again toggles you back to the Area 2
display.
22.3 Arm/Disarm all Areas at the Same
Time
If the system is partitioned into multiple areas, a user
can arm or disarm all assigned areas at the same
time. Your security company must program this
feature before it works.
can arm or disarm all assigned areas at the same
time. Your security company must program this
feature before it works.
How to Arm/Disarm all Areas at the Same Time
Enter your code followed by [0] and the [#] key (for
example [2 5 8 0 0 #]).
example [2 5 8 0 0 #]).
V2.03+: If you attempt to turn all areas on
and one or more zones are unsealed
(faulted) in any of the areas, the system
does not allow you to turn all areas on if
forced arming is disabled. You need to
restore all unsealed (faulted) zones before
the system allows you to turn all areas on
at the same time.
and one or more zones are unsealed
(faulted) in any of the areas, the system
does not allow you to turn all areas on if
forced arming is disabled. You need to
restore all unsealed (faulted) zones before
the system allows you to turn all areas on
at the same time.
23.0 Remote Arming By
Telephone
Use this feature to arm your system from any remote
location by telephone. For obvious security reasons,
the system cannot be disarmed using this method. To
make use of this feature, a touch-tone telephone is
required. Your security company needs to program
this feature to operate.
location by telephone. For obvious security reasons,
the system cannot be disarmed using this method. To
make use of this feature, a touch-tone telephone is
required. Your security company needs to program
this feature to operate.
How to Remotely Arm Your System by the
Telephone
Telephone
1. Call the telephone number your control panel
connects to.
2. With a DTMF command module, press the [#]
key on a touch-tone telephone keypad to
remotely arm the system.
If you hear modem tones when the control panel
answers the incoming call, this means the system
was programmed for remote programming
functions by your installer. Simply wait for a
pause between the tones before pressing the [*]
button.
Two beeps are heard to indicate that the system
is armed in AWAY Mode.
remotely arm the system.
If you hear modem tones when the control panel
answers the incoming call, this means the system
was programmed for remote programming
functions by your installer. Simply wait for a
pause between the tones before pressing the [*]
button.
Two beeps are heard to indicate that the system
is armed in AWAY Mode.
3. Hang up the telephone and the system remains
armed.
If your installer programs answering
machine bypass, call the control panel
twice to make a connection with the
system. For example, call the telephone
number your control panel is connected to
and let the call ring no more than four rings.
Hang up the telephone. Wait a minimum of
8 sec. before you call the control panel
back.
machine bypass, call the control panel
twice to make a connection with the
system. For example, call the telephone
number your control panel is connected to
and let the call ring no more than four rings.
Hang up the telephone. Wait a minimum of
8 sec. before you call the control panel
back.
24.0 Operating the System by a
Touch-Tone Telephone
If the system is installed with an optional DTMF
command module, the system can be operated by a
touch-tone telephone. Once a communication link is
established between a touch-tone telephone and your
alarm system, you can operate the system by the
telephone as if you were operating the system from a
codepad.
command module, the system can be operated by a
touch-tone telephone. Once a communication link is
established between a touch-tone telephone and your
alarm system, you can operate the system by the
telephone as if you were operating the system from a
codepad.
How to Establish a Communication Link
1. Dial the telephone number the system is
connected to. When the system answers your
call, you hear a short jingle.
call, you hear a short jingle.
2. Press the [0] key on your telephone. If the system
registered the tone generated by pressing the [0]
key, you hear a second jingle. You have
established a link.
If your system is partitioned, press the key that
corresponds to the area that you want to
establish a connection to (for example, press [1]
for Area 1, [2] for Area 2, [3] for Area 3, and [4]
for Area 4).
key, you hear a second jingle. You have
established a link.
If your system is partitioned, press the key that
corresponds to the area that you want to
establish a connection to (for example, press [1]
for Area 1, [2] for Area 2, [3] for Area 3, and [4]
for Area 4).
3. You can now operate the system as if you were
at the codepad.
Once you establish a link with a system
that is partitioned, you cannot toggle
between areas by pressing the [#] key (see
Section 22.1.3 Area Display Indicators).
You are required to establish separate
connections for each area that you want to
operate.
that is partitioned, you cannot toggle
between areas by pressing the [#] key (see
Section 22.1.3 Area Display Indicators).
You are required to establish separate
connections for each area that you want to
operate.
How to Terminate a Communication Link
Press the [#] key on the telephone twice to terminate
the link. You hear tones of decreasing pitch to
indicate termination of the link.
Alternatively, you can hang up the telephone and the
system disconnects from the telephone network after
60 seconds.
the link. You hear tones of decreasing pitch to
indicate termination of the link.
Alternatively, you can hang up the telephone and the
system disconnects from the telephone network after
60 seconds.