Electrolux EI30DS55LW Installation Instruction
30" DUAL FUEL SLIDE-IN RANGE INSTALLATION INSTRUCTIONS
(Models with an Electric Oven and a Gas Cooktop)
5
Electrical Shock Hazard
• Electrical ground is required on this appliance.
• Do not connect to the electrical supply until
• Do not connect to the electrical supply until
appliance is permanently grounded.
• Disconnect power to the circuit breaker or fuse
box before making the electrical connection.
• This appliance must be connected to a
grounded, metallic, permanent wiring system,
or a grounding connector should be connected
to the grounding terminal or wire lead on the
appliance.
or a grounding connector should be connected
to the grounding terminal or wire lead on the
appliance.
Failure to do any of the above could result in a
fire, personal injury or electrical shock.
Figure 1
1
Power Supply Cord Kit (U.S.A.)
The user is responsible for connecting the power supply
cord to the connection block located behind the back
panel access cover.
This appliance may be connected by means of
permanent "hard wiring" (flexible armored or
nonmetallic shielded copper cable), or by means of a
power supply cord kit. Only a power supply cord kit
rated at 125/250 volts 30 Amps should be used. Cord
must have either 3 or 4 conductors.
cord to the connection block located behind the back
panel access cover.
This appliance may be connected by means of
permanent "hard wiring" (flexible armored or
nonmetallic shielded copper cable), or by means of a
power supply cord kit. Only a power supply cord kit
rated at 125/250 volts 30 Amps should be used. Cord
must have either 3 or 4 conductors.
For mobile homes, new installations, recreational
vehicles, or areas where local codes do not permit
grounding through neutral, a 4 conductor power supply
cord kit rated at 125/250 volts 30 Amps marked for use
with ranges should be used.
vehicles, or areas where local codes do not permit
grounding through neutral, a 4 conductor power supply
cord kit rated at 125/250 volts 30 Amps marked for use
with ranges should be used.
Terminals on end of wires must be either closed loop or
open-end spade lugs with upturned ends. Cord must
have strain-relief clamp.
open-end spade lugs with upturned ends. Cord must
have strain-relief clamp.
NOTE: Electric Slide-in Range is shipped from factory
with 1 1/8" (2.9 cm) dia. hole as shown on figure 3. If a
larger hole is required, punch out the knockout.
with 1 1/8" (2.9 cm) dia. hole as shown on figure 3. If a
larger hole is required, punch out the knockout.
Breaker Size:
On a unit with 4800W or less at 240V (see serial plate),
a 20A circuit breaker or time-delay fuse is recommended
on both side of the line (red and black wire). DO NOT
fuse the neutral (white wire) or the ground (green or
bare wire).
On a unit with higher than 4800W at 240V (see serial
plate), follow the above recommendations but use a 30A
circuit breaker or time-delay fuse.
On a unit with 4800W or less at 240V (see serial plate),
a 20A circuit breaker or time-delay fuse is recommended
on both side of the line (red and black wire). DO NOT
fuse the neutral (white wire) or the ground (green or
bare wire).
On a unit with higher than 4800W at 240V (see serial
plate), follow the above recommendations but use a 30A
circuit breaker or time-delay fuse.
Risk of fire or electrical shock exists
if an incorrect size range cord kit is used, the
Installation Instructions are not followed, or the
strain relief bracket is discarded.
Installation Instructions are not followed, or the
strain relief bracket is discarded.
Do not loosen the nuts which secure
the factory-installed range wiring to terminal block
while connecting range. Electrical failure or loss of
electrical connection may occur.
while connecting range. Electrical failure or loss of
electrical connection may occur.
2
Factory Connected Power Supply
Cord (Canada only)
This range is equipped with a factory-connected power
cord (see Figure 1). Cord must be connected to a
grounded 120/240 volt or 120/208 volt range outlet. If
not outlet is available, have one installed by a qualified
electrician.
cord (see Figure 1). Cord must be connected to a
grounded 120/240 volt or 120/208 volt range outlet. If
not outlet is available, have one installed by a qualified
electrician.