Samsung CLX-6250 Manual De Usuario

Supplies and accessories_ 7

8. Install the control board cover with the screws removed in step 3.

9. Install the rear cover with the screws removed in step 2.
10. Plug all the cables back into the machine, and turn the machine on.
11. Set the wireless network environment.

For information about configuring and using the printer on a 

wireless network environment, refer to the Wireless network install 

guide provided with the wireless network interface card. You can 

also configure the network parameters on the control panel; see 

the next column.

Before starting you will need to know the network name(SSID) of your 

wireless network and the network key if it is encrypted. This information was 

set when the wireless router(access point) was installed. If you do not know 

about your wireless environment, please ask the person who has set up 

your network.
To configure wireless parameters, you can use both control panel and 

SyncThru™ Web Service.

1.Press Menu on the control panel.
2.Press the up/down arrow to highlight Network and press OK.
3.Press the up/down arrow to highlight Wireless and press OK.
4.Press the up/down arrow to highlight WLAN Settings and press OK.
5.Press the up/down arrow to select the setup method you want is 

highlighted and press OK.

•

Wizard: The wireless network interface card in your printer 

searches for wireless networks in the area and shows the results.

•

Custom: You can configure the wireless settings according to your 

needs.

1.The wireless network interface card on your machine searches for 

wireless network in the area and shows the results.

2.Press the up/down arrow to select a network you want to use in 

Search List and press OK. You can select a network using SSID.

3.When None appears in WLAN Security on the display, press OK to 

save your selection. go to step 6.
If you see another messages, go to the next step.

4.According to the network you select, WLAN security encryption type 

will be WEP or WPA.

•

In case of WEP, Press the up/down to selcet Open System or 

SharedKey.

-

Open System: Authentication is not used, and Encryption 

may or may not be used, depending on the need for data 

security. Enter the WEP Key using number keypad after 

selecting Open System.

-

SharedKey: Authentication is used. A device that has a proper 

WEP Key can access the network. Enter the WEP Key using 

number keypad after selecting SharedKey.

•

In case of WPA, Enter the WPA Key using number keypad. The 

Key length should be between 8 to 63 characters long.

5.Press OK.
6.Press Stop/Clear to return to ready mode.

•

SSID: SSID (Service Set Identifier) is a name that identifies a 

wireless network. Access points and wireless devices 

attempting to connect to a specific wireless network must use 

the same SSID. The SSID is case-sensitive.

•

WEP : WEP (Wired Equivalent Privacy) is a security protocol 

preventing unauthorized access to your wireless network. 

WEP encrypts the data portion of each packet exchanged on a 

wireless network using a 64-bit or 128-bit WEP encryption key.

•

WPA : WPA authorizes and identifies users based on a secret 

key that changes automatically at regular intervals. WPA also 

uses TKIP (Temporal Key Integrity Protocol) and AES 

(Advanced Encryption Standard) for data encryption.

1.Enter the SSID when Edit SSID appears on the top line of the display, 

the name that identifies a wireless network. SSID is case-sensitive 

so you need to enter it carefully. Press OK.

2.Select the type of wireless connections. Press the up/down arrow to 

select the method of Operation Mode you want and press OK.

•

Ad-hoc: Allows wireless devices to communicate directly with each 

other in a peer-to-peer environment. Go to step 3.

•

Infrastructure: Allows wireless devices to communicate with each 

other through an access point. Go to step 4.

3.Press the up/down arrow to select the method of Channel you want 

and press OK. If you select Auto, the wireless network interface card 

on your machine will automatically adjust the channels.

4.Press the up/down arrow to select the method of WLAN Security you 

want and press OK.

•

None: This is used when the validation of a wireless device’s 

identity and data encryption are not required for your network. 

Open system is used for IEEE 802.11 authentication.

•

Static WEP: This uses the WEP (Wired Equivalent Privacy) 

algorithm suggested by IEEE 802.11 standard for security. Static 

WEP security mode requires a proper WEP key for data 

encryption, decryption, and IEEE 802.11 authentication. Press 

the left/right arrow to select the setup method you want in 

Authentication and press OK.