Cisco Systems ASR 1000 Series Manual De Usuario
2-23
Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation and Initial Configuration Guide
OL-13208-03
Chapter 2 Cisco ASR 1000 Series Routers Components
Cisco ASR 1000 Series Router Power Supplies
AC/DC Power System Output for Cisco ASR 1006
under all combinations of line variation.
Total system consumption per power supply should not exceed 1200 W.
Power Supplies for Cisco ASR 1004 Router
The Cisco ASR 1004 Router can support up to 735 W output (AC and DC input). The 735W power
supply module consists of either an AC or DC input with two DC voltage outputs: 12V and 3.3V.
supply module consists of either an AC or DC input with two DC voltage outputs: 12V and 3.3V.
Each power supply module contains three internal fan modules and provides the forced air cooling for
the chassis. These power supply modules contain a monitor circuit to determine the status of fan speed
and operation along with LED status indicating fan errors.
the chassis. These power supply modules contain a monitor circuit to determine the status of fan speed
and operation along with LED status indicating fan errors.
The system temperature operation is 0 to 40C and –5C to +55C.
•
AC System—AC power input is an IEC 320-type power inlet, 15A service connector. The AC input
side contains a front panel with provisions for mounting screw, built in handle to remove the power
supply, three status LEDs, and fans for power supply and system cooling.
side contains a front panel with provisions for mounting screw, built in handle to remove the power
supply, three status LEDs, and fans for power supply and system cooling.
•
DC System—Three-position terminal block-style connector, with labeled connections for -
(–48/60 V input) and + (–48/60 V Return) and GND (earth ground symbol). The DC input side
contains a front panel with provisions for mounting screw, built in handle to extract the power
supply, three status LEDs, and fans for power supply and system cooling.
(–48/60 V input) and + (–48/60 V Return) and GND (earth ground symbol). The DC input side
contains a front panel with provisions for mounting screw, built in handle to extract the power
supply, three status LEDs, and fans for power supply and system cooling.
See
for detailed power supply
specifications.
Warning
This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that
the protective device is rated not greater than: AC power supplies for the Cisco Aggregation Services
Routers: 120 VAC, 20A U.S. maximum. DC power supplies for the Cisco ASR 1006 Router: 50A U.S.
maximum; Cisco ASR 1004 Router: 40A U.S. maximum: Cisco ASR 1002 Router: 30A U.S. maximum.
Statement 1005
the protective device is rated not greater than: AC power supplies for the Cisco Aggregation Services
Routers: 120 VAC, 20A U.S. maximum. DC power supplies for the Cisco ASR 1006 Router: 50A U.S.
maximum; Cisco ASR 1004 Router: 40A U.S. maximum: Cisco ASR 1002 Router: 30A U.S. maximum.
Statement 1005
Cisco ASR 1004 AC Power Supply
This section provides information about the AC power supplies on the rear of the Cisco ASR 1004
Router. The power supply module contains three fans mounted in the power supply module. A total of
six fans are used to cool the ASR 1004 system and power supply. The airflow direction is front to back.
Router. The power supply module contains three fans mounted in the power supply module. A total of
six fans are used to cool the ASR 1004 system and power supply. The airflow direction is front to back.
Table 2-13
Cisco ASR 1006 Router Power System Output Voltage and Current
Output Voltage
+12 VDC
+3.3 V
Minimum
11.80 VDC
3.20 VDC
Nominal
12.00 VDC
3.30 VDC
Maximum
12.20 VDC
3.40 VDC
Output Current
Minimum
2.80 A
0.10 A
Maximum
101.7 A
3.125 A