Cisco Systems OL-7396-01 Manual De Usuario
17-6
ATM Switch Router Software Configuration Guide
OL-7396-01
Chapter 17
Configuring Signalling Features
Configuring E.164 Addresses
Configuring an E.164 Address Static Route
To configure an E.164 address static route, use the following command in global configuration mode:
Example
The following example uses the atm route command to configure a static route using the 13-byte switch
prefix 47.00918100000000410B0A1081 to ATM interface 0/0/0 with the E.164 address 1234567:
prefix 47.00918100000000410B0A1081 to ATM interface 0/0/0 with the E.164 address 1234567:
Switch(config)# atm route 47.00918100000000410B0A1081 atm 0/0/0 e164-address 7654321
To complete the E.164 address static route configuration, proceed to the
Displaying the E.164 Static Route Configuration
To display the E.164 address configuration, use the following privileged EXEC command:
Example
The following example displays the E.164 address configuration using the show atm route privileged
EXEC command:
EXEC command:
Switch# show atm route
Codes: P - installing Protocol (S - Static, P - PNNI, R - Routing control),
T - Type (I - Internal prefix, E - Exterior prefix, SE -
Summary Exterior prefix, SI - Summary Internal prefix,
ZE - Suppress Summary Exterior, ZI - Suppress Summary Internal)
P T Node/Port St Lev Prefix
~ ~~ ~~~~~~~~~~~~~~~~ ~~ ~~~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
S E 1 ATM0/1/0 DN 0 47.0091.8100.0000.0001/72
P SI 1 0 UP 0 47.0091.8100.0000.0002.eb1f.fe00/104
R I 1 ATM2/0/0 UP 0 47.0091.8100.0000.0002.eb1f.fe00.0002.eb1f.fe00/152
R I 1 ATM2/0/0 UP 0 47.0091.8100.0000.0002.eb1f.fe00.4000.0c/128
P SI 1 0 UP 0 47.0091.8100.0000.0040.0b0a.2b81/104
S E 1 ATM0/0/0 DN 0 47.0091.8100.0000.0040.0b0a.2b81/104
(E164 Address 1234567)
R I 1 ATM2/0/0 UP 0 47.0091.8100.0000.0040.0b0a.2b81.0040.0b0a.2b81/152
R I 1 ATM2/0/0 UP 0 47.0091.8100.0000.0040.0b0a.2b81.4000.0c/128
Configuring an ATM E.164 Address on an Interface
One E.164 address can be configured per ATM port. Signalling uses E.164 addresses in the called and
calling party IEs, and uses AESA addresses in the called and calling party subaddress IEs.
calling party IEs, and uses AESA addresses in the called and calling party subaddress IEs.
Command
Purpose
atm route address-prefix atm card/subcard/port
[e164-address address-string [number-type
{international | local | national | subscriber}]]
[internal] [scope org-scope]
[e164-address address-string [number-type
{international | local | national | subscriber}]]
[internal] [scope org-scope]
At the configure prompt, configures the static
route prefix with the E.164 address.
route prefix with the E.164 address.
Command
Purpose
show atm route
Displays the static route E.164 address
configuration.
configuration.