Toshiba RAS-10 N3KV-E/RAS-10 N3AV-E Manual De Usuario

In case of the misplaced or discharged remote control
  •  Pressing the RESET button, the unit can start or 

stop without using the remote control.

  •  Operation mode is set on AUTOMATIC operation, 

preset temperature is 25°C and fan operation is 
automatic speed.

Press 

  :  Set the desired ON 

timer.

Press 

  :  Set the desired 

OFF timer.

Press 

  :  Set the timer.

Press 

  :  Set the timer.

Press 

 :  Cancel the timer.

Press 

  :  Cancel the timer.

Press

 

 

: Set the ON timer.

Press 

.

Press

 

 

: Set the OFF timer.

Press 

 button during 

the (  or  ) mark fl ashing.

  •  During the daily timer is activating, both arrows (  ,  ) are indicated.
Note:
  •  Keep the remote control in accessible transmission to the indoor unit; 

otherwise, the time lag of up to 15 minutes will occur.

  •  The setting will be saved for the next same operation.

Set your preferred operation for future use. The setting will be memorized by 
the unit for future operation (except airfl ow direction).
  1. Select your preferred operation.

  2. Press and hold 

 for 3 seconds to memorize the setting. 

The P mark displays.

 3. 

Press 

 : Operate the preset operation.

To automatically restart the conditioner after the power failure (Power of the 
unit must be on.)
Setting
  1. Press and hold the RESET button on the indoor unit for 3 seconds to 

set the operation. (3 beep sound and OPERATION lamp blink 5 time/
sec for 5 seconds)

  2. Press and hold the RESET button on the indoor unit for 3 seconds to 

cancel the operation. (3 beep sound but OPERATION lamp does not 
blink)

    •  In case of ON timer or OFF timer are set, AUTO RESTART 

OPERATION does not activate.

To operate at super low fan speed for quiet operation (except in DRY mode)

 Press 

48,(7

 : Start and stop the operation.

Note:  Under certain conditions, QUIET operation may not provide adequate 

cooling or heating due to  low sound features.

To save energy while sleeping, automatically control air fl ow and 
automatically turn OFF.

 Press 

 : Select 1, 3, 5 or 9 hrs for OFF timer operation.

Note: The cooling operation, the set temperature will increase automatically 

1 degree/hour for 2 hours (maximum 2 degrees increase). For heating 
operation, the set temperature will decrease.

  1. Three-minute protection feature: To prevent the unit from being 

activated for 3 minutes when suddenly restarted or switched to ON.

  2. Preheating operation: Warm up the unit for 5 minutes before the heating 

operation starts.

  3. Warm air control: When the room temperature reaches the set 

temperature, the fan speed is automatically reduced and the outdoor 
unit will stop.

  4.  Automatic defrosting: Fans will stop during defrost operation.
  5.  Heating capacity: Heat is absorbed from outdoors and released into 

the room. When the outdoor temperature is too low, use another 
recommended heating apparatus in combination with the air conditioner.

  6. Consideration for accumulated snow: Select the position for outdoor unit 

where it will not be subjected to snow drifts, accumulation of leaves or 
other seasonal debris.

  7. Some minor cracking sound may occur when unit operating. This is 

normal because the cracking sound may be caused by expansion/
contraction of plastic.

  Note: Item 2 to 6 for Heating model
Air conditioner operating conditions

Heating

–10°C ~ 24°C

Less than 28°C

Cooling

15°C ~ 43°C

21°C ~ 32°C

Dry

15°C ~ 43°C

17°C ~ 32°C

•  The power main switch is 

turned off.

•  The circuit breaker is 

activated to cut off the power 
supply.

•  Stoppage of electric current
•  ON timer is set.

• The fi lters are blocked with dust.
•   The temperature has been set 

improperly.

•   The windows or doors are opened.
•   The air inlet or outlet of the outdoor 

unit is blocked.

•   The fan speed is too low.
•   The operation mode is FAN or DRY.

To separate using of remote control for each indoor unit in case of 2 air 
conditioners are installed nearly.
Remote Control B Setup.
  1. Press RESET button on the indoor unit to turn the air conditioner ON.
  2. Point the remote control at the indoor unit.
  3. Push and hold 

 button on the Remote Control by the tip of the 

pencil. “00” will be shown on the display.

 4. 

Press 

02'(

 during pushing 

. “B” will show on the display and 

“00” will disappear and the air conditioner will turn OFF. The Remote 
Control B is memorized.

Note:   1.  Repeat above step to reset Remote Control to be A.
 

2.  Remote Control A has not “A” display.

 

3.  Default setting of Remote Control from factory is A.

0

 Firstly, turn off the circuit breaker.

Filter Reset (Some models only)
FILTER lamp lights on; the fi lter must be cleaned.
To turn off the lamp, push the RESET button on the indoor unit or the FILTER 
button on the remote control.

Indoor Unit and Remote Control
  •  Clean the indoor unit and the remote control with a wet cloth when 

needed.

  •  No benzine, thinner, polishing powder or chemically-treated duster.

To protect bad smell caused by the humidity in the indoor unit.

 1. 

If 

the 

 button is pressed once during “Cool” or “Dry” mode, 

the fan will continue to run for other 30 minutes, then it will turn off 
automatically. This will reduce the moisture in the indoor unit.

  2. To stop the unit immediately, press the 

 more 2 times 

within 30 seconds.

EN

1

2

1113950109_EN.indd   3

1113950109_EN.indd   3

8/8/12   11:08 AM

8/8/12   11:08 AM