Crestron Electronics Inc CWD1011 Manual De Usuario

  

 

Hot

Neutral

Load

RED

BLACK

WHITE

BLUE

Ground

GREEN

LINE

120VAC

60Hz

60Hz

120VAC

LINE

GREEN

Ground

WHITE

BLACK

RED

Load

Neutral

Hot

 

NOTE:  The -DIMS1RF must be installed in the same 
wallbox that contains the connections to the load. 

NOTE:  The -DIM1RF, -DIMS1RF, and -SLVD1RF 
require a neutral wire for operation. If no neutral is 
present, contact a licensed electrician for installation or 
contact Crestron Customer Service for alternative wiring 
options. 

WARNING:  Turn off power at the circuit breaker. 
Installing with power on can result in serious personal 
injury and damage to the device. 

NOTE:  The RED (Load) and BLACK (Hot) wires are 
#14 AWG. The BLUE (Slave) and WHITE (Neutral) 
wires are #18 AWG. The GREEN (Ground) wire is #16 
AWG.  

NOTE:  New installations should be checked for short 
circuits prior to installing the -DIM1RF, -DIMS1RF, or  
-SLVD1RF. With power off, close the circuit and restore 
power. If the lights do not work or a breaker trips, check 
and correct the wiring or fixture (if necessary). Install the 
-DIM1RF, -DIMS1RF, or -SLVD1RF only when the 
short is no longer present. The warranty is void if the  
-DIM1RF, -DIMS1RF, or -SLVD1RF is installed and 
operated with a shorted load. 

NOTE: The -DIMS1RF must be installed in the same 
wallbox that contains the connections to the load. 

The following wiring diagram illustrates installation of 
the -DIMS1RF with multiple -SLVD1RFs. 

1.  Turn power off at the circuit breaker. 

2.  If installing multiple dimmers (-DIM1RF or  

-DIMS1RF), note the serial number on each 
device and make sure they are being installed in 
the proper location. 

Hot

Neutral

Load

RED

CLW-DIMS1RF

BLACK

WHITE

CLW-SLVD1RF

BLUE

BLACK

BLUE

Ground

Ground

GREEN

GREEN

LINE

120VAC

60Hz

WHITE

Ground

GREEN

BLACK

BLUE

CLW-SLVD1RF

WHITE

 

3.  Wire the device for the appropriate application. 

Choose either “CLW-DIM1RF / CLW-
DIMS1RF Wiring” or “CLW-DIMS1RF with 
CLW-SLVD1RF Wiring”, shown on this page 
and the following page. 

NOTE:  Alternative wiring methods can be obtained from 
the Dealer/Tech Resources | Design Center section of the 
Crestron website (http://www.crestron.com/dealer-
tech_resources/design_center/hot_design_tips_and_ 
diagrams/tech_sales_tips/). 

NOTE:  Do not connect the BLUE (Slave) wire to the 
Black (Hot) or RED (Load) wires. 

NOTE:  The RED (Load) and BLACK (Hot) wires are 
#14 AWG. The BLUE (Slave) and WHITE (Neutral) 
wires are #18 AWG. The GREEN (Ground) wire is #16 
AWG.  

NOTE:  The -DIM1RF and -DIMS1RF require a neutral 
wire for operation. If no neutral is present, contact a 
licensed electrician for installation or contact Crestron 
customer service for alternative wiring options. 

NOTE:  If a -DIMS1RF is installed without a  
-SLVD1RF, the BLUE lead (Slave) should be capped. 

The following wiring diagram illustrates installation of 
the -DIM1RF or -DIMS1RF. 

4.  Push all Class 1 power wires back into the 

wallbox and fasten the device to the wallbox 
with the provided screws. 

5.  Attach decorative faceplate. 

6. Restore 

power. 

•  Stand Alone Wall Box Dimmer :  CLW-DIM1RF, DIMS1RF, & SLVD1RF