ADC Telecommunications Inc. PSM230WM Manual De Usuario
Page 20
FlexWave Prism Remote Unit RF Module Installation Guide
©2015 TE Connectivity
TECP-77-141 Issue 8 • 300001744178 Rev H • August 2015
RF Module Cables and Supported Bay Installations for Legacy Dual-Bay 40W RF Modules
for Legacy Dual-Bay 40W RF Modules.
also shows which RF Module type can be installed in which PRU bay(s) when a 40W Dual-Bay RF Module
is part of the RF Module mix in a PRU chassis. The Single-Bay chassis is not included in
.
For Dual-Bay installations, the RF cables and connectors are labeled as MOD N TX0/RX0 and MOD N TX1/RX1,
where N refers to the top bay of the double-bay installation. For example:
•
For a Dual-Bay installation in a Quad-Bay chassis in which the RF Module is installed in the Bay D and Bay C
combination, the RF cables and connectors are labeled as MOD D TX0/RX0 and MOD D TX1/RX1.
combination, the RF cables and connectors are labeled as MOD D TX0/RX0 and MOD D TX1/RX1.
•
For a Dual-Bay installation in a Tri-Bay chassis in which the RF Module is installed in the Bay C and Bay B
combination, the RF cables and connectors are labeled as MOD C TX0/RX0 and MOD C TX1/RX1.
combination, the RF cables and connectors are labeled as MOD C TX0/RX0 and MOD C TX1/RX1.
Table 12.
Supported Bay Assignments and RF Antenna Labels for Legacy Dual-Bay 40W RF Modules
(From Top of Remote Unit Chassis Down)
Supported Bay Combinations for Legacy 40W Dual-Bay RF Modules
RF Module
Cable,
RF Module
Connector, and
Remote Antenna
Connector Label
Function
Dual-Bay
Tri-Bay
Tri-Bay
Quad-Bay
Bay D
N/A
N/A
N/A
MOD D
MOD D
MOD C
Mod D TX0/RX0
Transmit RF power and
primary/Path 1 receive to/from
the antenna for RF Module D
primary/Path 1 receive to/from
the antenna for RF Module D
Mod D TX1/RX1
Transmit RF power and
secondary/Path 2 receive
to/from the antenna for RF
Module D
secondary/Path 2 receive
to/from the antenna for RF
Module D
Bay C
N/A
MOD C
MOD C
MOD C
Mod C TX0/RX0
Transmit RF power and
primary/Path 1 receive to/from
the antenna for RF Module C
primary/Path 1 receive to/from
the antenna for RF Module C
Mod C TX1/RX1
Transmit RF power and
secondary/Path 2 receive
to/from the antenna for RF
Module C
secondary/Path 2 receive
to/from the antenna for RF
Module C
Bay B
MOD B
MOD B
MOD B
MOD B
MOD B
Mod B TX0/RX0
Transmit RF power and
primary/Path 1receive to/from
the antenna for RF Module B
primary/Path 1receive to/from
the antenna for RF Module B
Mod B TX1/RX1
Transmit RF power and
secondary/Path 2 receive
to/from the antenna for RF
Module B
secondary/Path 2 receive
to/from the antenna for RF
Module B
Bay A
MOD A
MOD A
Mod A TX0/RX0
Transmit RF power and
primary/Path 1 receive to/from
the antenna for RF Module A
primary/Path 1 receive to/from
the antenna for RF Module A
Mod A TX1/RX1
Transmit RF power and
secondary/Path 2 receive
to/from the antenna for RF
Module A
secondary/Path 2 receive
to/from the antenna for RF
Module A
Note:
For Dual Module installations the center module shelf needs to be removed; see
.
Note:
Install the Legacy Dual-Bay 40W RF Module in the lower-most bay in the chassis. If, however, if two Legacy Dual-Bay 40W RF Modules
are present, install the 2100 Module in the lower-most Bay and the 1900 Module in the upper-most Bay.
are present, install the 2100 Module in the lower-most Bay and the 1900 Module in the upper-most Bay.