Superchips Inc. Car Stereo System 1715 maz Manual De Usuario
Page 5 of 16
Form 0129L 03/29/07
Superchips Inc
.
Superchips Inc.
1790 East Airport Blvd., Sanford, FL. 32773 (407) 585-7000 http://www.Superchips.com
Superchip & Superchips are registered trademarks of Superchips, Inc.
Insure the ignition switch is OFF, then press the ‘>’ key on the keypad.
The MAX MicroTuner alternately displays the following messages:
Turn Ignition ON
then
Press >
Do NOT START Eng
to Continue…
2. Selecting Tune Vehicle / Diagnostics
Turn the ignition switch to the ON position. Press the ‘>’ key on the keypad. The MAX
MicroTuner will beep and display the message:
MicroTuner will beep and display the message:
A= Tune Vehicle
B= Diagnostics
B= Diagnostics
Press the ‘A’ key on the keypad to continue with the tuning process.
Press the ‘B’ key to read and/or clear any Diagnostic Trouble Codes from the vehicle.
See provided Reader Instructions and Code Interpretations in the separate manual
for this purpose with your MAX Micro tuner.
See provided Reader Instructions and Code Interpretations in the separate manual
for this purpose with your MAX Micro tuner.
3. Vehicle Programming
The MAX MicroTuner will beep and display the message:
Is FUEL System
Disabled YES/NO?
Disabled YES/NO?
If ‘NO’ is pressed, the MAX MicroTuner will beep and display the following messages:
FUEL System Must
then
See Tuner Manual
Be Disabled 1st!
for Procedure…
then
Press Any Key
To Continue…
To Continue…
After pressing a key, the MAX MicroTuner beeps and returns to
Selecting Tune Vehicle / Diagnostics
at Step 2.
If ‘YES’ is pressed, the MAX MicroTuner will proceed to establish communications and
display the following message:
display the following message:
Establishing
Communications
Communications
The MAX MicroTuner is establishing communications with and identifying the vehicle
computer. If the MAX MicroTuner has not yet been used to program a vehicle, no vehicle
ID will be stored in the MAX MicroTuner. In such a case, the MAX MicroTuner will begin
saving the STOCK program for the vehicle. If the vehicle ID matches a vehicle ID stored in
the MicroTuner, the MAX MicroTuner will go directly to the Return to Stock Sequence
Section at Step 10 that follows.
computer. If the MAX MicroTuner has not yet been used to program a vehicle, no vehicle
ID will be stored in the MAX MicroTuner. In such a case, the MAX MicroTuner will begin
saving the STOCK program for the vehicle. If the vehicle ID matches a vehicle ID stored in
the MicroTuner, the MAX MicroTuner will go directly to the Return to Stock Sequence
Section at Step 10 that follows.
Not the Original
then
Error Type: 09 *
Vehicle/Program
Call
Superchips!
then
Press '>' to
Continue...
Continue...
*
Other error codes, with or without explanations may be displayed.
Pressing the ‘>’ key will cause the MAX MicroTuner to beep and display the message:
Please Wait...
After a few seconds the MAX MicroTuner resets and returns to the power-up self test.
Page 6 of 16
Form 0129L 03/29/07
Superchips Inc
.
Superchips Inc.
1790 East Airport Blvd., Sanford, FL. 32773 (407) 585-7000 http://www.Superchips.com
Superchip & Superchips are registered trademarks of Superchips, Inc.
4. Saving the STOCK program for the vehicle
The manufacturer’s STOCK program is first saved in the MAX MicroTuner to allow the
vehicle to be reprogrammed to STOCK condition if necessary. The STOCK program is
saved only the first time the vehicle is programmed.
vehicle to be reprogrammed to STOCK condition if necessary. The STOCK program is
saved only the first time the vehicle is programmed.
Once the MAX MicroTuner has established communications, it will beep and display the
message:
message:
Turn Ignition
OFF Press >
OFF Press >
Turn the ignition to the OFF position and press the ‘>’ key on the keypad. The MAX
MicroTuner will beep and blink the following message for approximately 6 seconds:
MicroTuner will beep and blink the following message for approximately 6 seconds:
Initialization..
Please Wait…
Please Wait…
After initialization is complete, the MAX MicroTuner will beep and display the message:
Turn Ignition ON
Do NOT START Eng
Do NOT START Eng
Turn the ignition to the ON position. The MAX MicroTuner will beep and start saving the
stock program. This will take about three minutes. The MAX MicroTuner will blink the
following message:
stock program. This will take about three minutes. The MAX MicroTuner will blink the
following message:
Saving Stock
The bottom line of the display shows the progress of the stock upload.
When completed, the MAX MicroTuner checks to see if the stock program it has uploaded
can be found in its internal database. If not it will display the message:
can be found in its internal database. If not it will display the message:
Tuner Requires
then
Call Superchips!
an Update…
or…
Check Vehicle
then
Press any key to
application…
continue...
If the stock upload is found in the internal database, the MAX MicroTuner will beep and
display the message:
display the message:
Please Wait…
The MAX MicroTuner is testing to see if the Passive Anti-Theft System (PATS) is active. If
PATS is active, the MAX MicroTuner will beep and display the message:
PATS is active, the MAX MicroTuner will beep and display the message:
Resetting PATS
Please Wait...
Please Wait...
If PATS is not active, the MAX MicroTuner automatically clears the vehicle DTCs then
displays the message:
displays the message:
Clearing DTCs
Please Wait…
The MAX MicroTuner will then beep and display the message:
Stock Saved!!!
Press >
Press >
5. Installing the Superchips Performance Program
The MAX MicroTuner allows for three levels of performance tuning.