Futaba 10CAG Manual De Instrucciónes
84
OFFSETs
DGGLWLRQDOÀLJKWFRQGLWLRQVDYDLODEOHVSHFL¿FDOO\IRUVDLOSODQHV
Unnecessary fuselage motion is generated when there are sudden changes in the servo position. Variations in the operating
time between channels can be suppressed by using the delay function (-dly-).
time between channels can be suppressed by using the delay function (-dly-).
NOTE: The same delay amount for elevator and rudder is recommended when using V-tail function.
7KH&*SURYLGHVRIIVHWWULPVWRDOORZWKHPRGHOHUDGGLWLRQDOVHWXSVDORQJZLWKWKHQRUPDOÀLJKWFRQGLWLRQ NORMAL,
START
START
, SPEED, DISTANCE and LANDING) These offset trims have same setting abilities basically except the switch and dial
assignment. For an example of trim settings, please see the following:
Adjustability:
6HSDUDWHDGMXVWPHQWVIRUHDFKDLOHURQHOHYDWRUUXGGHUDQGÀDSVHUYRIRUHDFK
6HSDUDWHDGMXVWPHQWVIRUHDFKDLOHURQHOHYDWRUUXGGHUDQGÀDSVHUYRIRUHDFK
condition.
• SWITCH G (10CAG) or E (10CHG) is programmed for NORMAL, START, and
SPEED
trims. SWITCH C is programmed for DISTANCE and LANDING trims. The
VZLWFKSRVLWLRQDVVLJQPHQWLVDGMXVWDEOH CONDITION/FUNCTION)
• TRIM item (Digital trim operation mode):
NORM
: normal trim operation mode,
MIX
: offset rate trim operation mode while mixing is on.
• Optional assignable knob (CAMBER MIX) to allow trimming in flight of the
DLOHURQDQGÀDSDFWLRQRIHDFKÀLJKWFRQGLWLRQ
*During OFFSET operation, the aileron and elevator travels are displayed on each
trim display in the Startup screen.
trim display in the Startup screen.
GOAL of EXAMPLE:
STEPS:
INPUTS:
S e t u p a START t o g a i n m a x i m u m
possible lift on launch.
Each Aileron: 50%.
Each Flap: 100%.
Elevator: -5% to compensate.
possible lift on launch.
Each Aileron: 50%.
Each Flap: 100%.
Elevator: -5% to compensate.
SWITCH (10CAG=G, 10CHG=E.)
Note: switch is assignable. (CONDITION)
Note: switch is assignable. (CONDITION)
KNOB(null)
Note: knob is assignable. (CAMBER MIX)
Note: knob is assignable. (CAMBER MIX)
Open OFFSET function.
for 1 second.
(If BASIC,
again.)
C
to OFFSET.
Switch to the START condition.
G ( 1 0 C A ) o r E ( 1 0 C H ) f r o m
NORMAL
to START.
Set the rates. (Ex: AIL1 and 2, 50%, FLP1
and 2, 100%, ELEV -5%.)
and 2, 100%, ELEV -5%.)
C
to AIL1.
to +50%.
C
to AIL2.
to +50%.
Repeat for, FLP1 and 2, ELEV.
Close the function.
Where next?
View additional model setups on the internet: www.futaba-rc.com\faq\
These additional flight conditions contain different offset trims to make the
saiplane perform certain maneuvers more easily. Aileron differential functions
may be set to provide separate rates per condition selected.
Prior to setting up OFFSET, you must activate the conditions and assign the
switches in the CONDITION/FUNCTION.
saiplane perform certain maneuvers more easily. Aileron differential functions
may be set to provide separate rates per condition selected.
Prior to setting up OFFSET, you must activate the conditions and assign the
switches in the CONDITION/FUNCTION.