Futaba 10CAG Manual De Instrucciónes
85
Camber Mixing (CAMBER MIX)(GLID):
This function adjusts the mixing rate of camber operation which operates the
ZLQJ FDPEHU DLOHURQV DQG ÀDSV LQ WKH QHJDWLYH DQG SRVLWLYH GLUHFWLRQV 7KH
DLOHURQÀDSDQGHOHYDWRUUDWHVFDQDOVREHDGMXVWHGLQGHSHQGHQWO\DQGDWWLWXGH
changes caused by camber operation can be corrected.
Also the operation reference point of camber control can be offset. (PRE)
ZLQJ FDPEHU DLOHURQV DQG ÀDSV LQ WKH QHJDWLYH DQG SRVLWLYH GLUHFWLRQV 7KH
DLOHURQÀDSDQGHOHYDWRUUDWHVFDQDOVREHDGMXVWHGLQGHSHQGHQWO\DQGDWWLWXGH
changes caused by camber operation can be corrected.
Also the operation reference point of camber control can be offset. (PRE)
NOTE: Camber control is not assigned at default.
GOAL of EXAMPLE:
STEPS:
INPUTS:
Ex: Set the mixing amount for aileron
to 40%, camber control to VR(E),
reference point to desired point.
to 40%, camber control to VR(E),
reference point to desired point.
Open the CAMBER MIX function.
for 1 second.
(If BASIC,
again.)
C
to CAMBER MIX.
Choose desired slider.
C
to VR.
to VR(E).
Adjust the mixing amount for AILE.
(Ex: adjust to 40%.)
(Ex: adjust to 40%.)
C
to AILE.
VR(E).
to 40%.
VR(E).
to 40%.
Set the reference point.
C
to PRE.
or
VR(E) to
desired point.
for one second.
Close menu.
Adjustability:
• Rate: -100% to +100%, with a default of +30%
• Reference point (PRE): The operation reference point of camber control can be offset. -100% to +100%, with a default of 0%.
• Rate: -100% to +100%, with a default of +30%
• Reference point (PRE): The operation reference point of camber control can be offset. -100% to +100%, with a default of 0%.
START DELAY
(GLID 1A+1F only):
START DELAY
automatically switches the offset trims (OFFSET) from the START
condition's trims to the normal condition's trims after the delay time (max.10sec.).
This delay time set by the -dly- item when activating the START condition. (It is
convenient for hand launch glider.)
This delay time set by the -dly- item when activating the START condition. (It is
convenient for hand launch glider.)
NOTE: The same delay amount for elevator and rudder is recommended when
using V-tail function.
using V-tail function.
Adjustability:
• Delay time (-dly-) range of 0 to 100%. The delay time is 10 second at 100%.
• Delay time (-dly-) range of 0 to 100%. The delay time is 10 second at 100%.
GOAL of EXAMPLE:
STEPS:
INPUTS:
Ex: delay time=5 second.
Open ADVANCE menu, then open START
DELAY
DELAY
function.
for 1 second.
(If ADVANCE,
again.)
C
to START DELAY.
Activate the function.
C
to MIX.
to OFF or ON.
Set the delay time.
(Ex: 50% each surface)
(Ex: 50% each surface)
C
to ELEV.
to 5O%.
C
to RUDD.
to 5O%.
Repeat as needed.
Close.