ALTINEX PE1005 Manual De Usuario
SPECIAL APPLICATION
400-0384-003
27
46) [MODERSI]
Set internal baud rate
47) [RDRSI]
Read internal baud rate
48) [OUTRSM]
Send memory data via
external RS-232
external RS-232
49) [OUTBSM]
Send memory data via
internal RS-232
internal RS-232
50) [OUTPDPM]
Send memory
data
to
plasma main card
51) [OUTVCM]
Send memory
data
to
plasma video card
52) [SENDRS]
Send data via external bus
53) [SENDBS]
Sends data via internal bus
54) [SENDPS]
Send data to display card
55) [SENDVS]
Send data to video card
56) [MDON]
Enable motion detector
57) [MDOFF]
Disable motion detector
58) [MD1]
Set approaching sub
59) [MD0]
Set departing sub
60) [SETMD]
Set detector trigger value
61) [SETTMD]
Set detector time delay
62) [MDTYPE]
Set detector type
63) [RDMD]
Read detector settings
64) [RSI]
Reset card ID
65) [SIDn]
Set ID of cards
66) [SIDnCi]
Set ID of a single card
67) [RSN]
Read ID number
7.4 PLASMA CONTROL WITH INTERNAL BUS
The PE1005
has the capability of sending
commands directly to the plasma’s internal bus or
to third-party video cards installed in the plasma.
This allows the user to control settings on the
display without having to use the menu buttons on
the display or with the remote control.
to third-party video cards installed in the plasma.
This allows the user to control settings on the
display without having to use the menu buttons on
the display or with the remote control.
As in the previous sections, commands are sent via
standard RS-232 communication. Commands may
be sent directly to the internal bus, or stored into
RS memory locations and recalled from the
memory location and sent to the bus. The
commands for communicating with the internal bus
are [OUTPDPM] and [SENDBS]. See the previous
sections for details on these two commands,
including restrictions on the number of characters
that may be stored or sent in a single command.
standard RS-232 communication. Commands may
be sent directly to the internal bus, or stored into
RS memory locations and recalled from the
memory location and sent to the bus. The
commands for communicating with the internal bus
are [OUTPDPM] and [SENDBS]. See the previous
sections for details on these two commands,
including restrictions on the number of characters
that may be stored or sent in a single command.
7.4.1 INTERNAL COMMAND FORMAT
The internal commands for the PE1005 are in
the following format and must contain the
protocols indicated:
the following format and must contain the
protocols indicated:
1.
Start of text. (STX)
%02
2.
Plasma ID (default)
%2A%2A
3.
Command ID
See Appendix A of the
Pioneer manual
mentioned earlier.
Pioneer manual
mentioned earlier.
4.
End of text. (ETX)
%03
7.4.2 SENDING COMMANDS TO INTERNAL BUS
The default baud rate for the PE1005 is 9600
baud. Prior to sending any commands, verify
both the plasma and PE1005 are set to 9600
baud.
baud. Prior to sending any commands, verify
both the plasma and PE1005 are set to 9600
baud.
In order to change setting values, the plasma
must be in adjustment mode. The plasma may
be placed into adjustment mode by sending the
command AJY.
must be in adjustment mode. The plasma may
be placed into adjustment mode by sending the
command AJY.
The following examples demonstrate
communication with the plasma through the
internal bus using both stored commands and
direct commands. All commands may be sent to
the plasma using either method.
communication with the plasma through the
internal bus using both stored commands and
direct commands. All commands may be sent to
the plasma using either method.
Example 1: Adjustment Mode
Place the plasma into adjustment mode by
sending the following command directly to the
internal bus:
sending the following command directly to the
internal bus:
[SENDBS<%02%2A%2AAJY%03>]