3com MS40-717X Manual De Usuario
8
© Copyright 2010 Schneider Electric All Rights Reserved.
F-26748-6
Precautions
General
Warning:
•
Electrical shock hazard! Disconnect the power supply (line power) before and during
installation to prevent electric shock and equipment damage.
installation to prevent electric shock and equipment damage.
•
Make all connections in accordance with the wiring diagram and in accordance with
national and local electrical codes. Use copper conductors only.
national and local electrical codes. Use copper conductors only.
Caution:
•
Avoid electrical noise interference. Do not install near large contactors, electrical
machinery, or welding equipment.
machinery, or welding equipment.
•
Avoid locations where excessive moisture, corrosive fumes, vibration, or explosive
vapors are present.
vapors are present.
Federal Communications Commission (FCC)
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in residential installations. This
equipment generates, uses, and can radiate radio frequency energy and may cause
harmful interference if not installed and used in accordance with the instructions. Even
when instructions are followed, there is no guarantee that interference will not occur in a
particular installation. If this equipment causes harmful interference to radio or television
reception— which can be determined by turning the equipment off and on—the user is
encouraged to try to correct the interference by one or more of the following measures:
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in residential installations. This
equipment generates, uses, and can radiate radio frequency energy and may cause
harmful interference if not installed and used in accordance with the instructions. Even
when instructions are followed, there is no guarantee that interference will not occur in a
particular installation. If this equipment causes harmful interference to radio or television
reception— which can be determined by turning the equipment off and on—the user is
encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment to an outlet on a circuit different from that to which the receiver
is connected.
is connected.
•
Consult the dealer or an experienced radio/television technician for help.
Canadian Department of Communications (DOC)
Note: This class B digital apparatus meets all requirements of the Canadian Interference-
Causing Equipment Regulations.
Causing Equipment Regulations.
Cet appareil numerique de la classe B respecte toutes les exigences du Reglement sur le
material broilleur du Canada.
material broilleur du Canada.
European Standard EN 55022
Warning: This is a class B (European Classification) product. In a domestic environment
this product may cause radio interference in which case the user may be required to take
adequate measures.
this product may cause radio interference in which case the user may be required to take
adequate measures.
Location
Caution:
•
To maintain NEMA Type 4 rating, use water tight 1/2" flexible conduit only, with 1/2"
conduit connector of the water tight type, TAC part number TF-711-02 or T&B #5332
(straight), TAC part number TF-713-02 or T&B #5352 (90°), or equivalent.
conduit connector of the water tight type, TAC part number TF-711-02 or T&B #5332
(straight), TAC part number TF-713-02 or T&B #5352 (90°), or equivalent.
•
For metric conduit applications using AM-756 conduit adapters, use the appropriate
metric water tight seals to maintain compliance with IP56 or NEMA Type 4 rating.
metric water tight seals to maintain compliance with IP56 or NEMA Type 4 rating.
•
Use a water tight 1/2" pipe plug in any unused actuator conduit ports and seal with
water tight tape to stay in compliance with NEMA Type 4 or IP56 rating. Use TAC part
number X-5521, Grinnell #8700159257 (black), Grinnell #8700159851 (galvanized), or
equivalent. Actuators with unused conduit ports are shipped with the unused port
plugged.
water tight tape to stay in compliance with NEMA Type 4 or IP56 rating. Use TAC part
number X-5521, Grinnell #8700159257 (black), Grinnell #8700159851 (galvanized), or
equivalent. Actuators with unused conduit ports are shipped with the unused port
plugged.