Keurig B50 Mode D'Emploi

IMPORTANT: You cannot use your Keurig
brewer until it has been primed for its first use
as set forth below.

1.  Unwrap cord and plug the brewer into a

grounded outlet.

2. Place a cup or mug on the Drip Tray Plate.

3. Remove the Water Reservoir from Brewer by

first removing Lid from Reservoir, then lifting
Reservoir straight up and away from Brewer
(may be tight). Rinse with fresh water.

4. Fill Water Reservoir with fresh water so 

that the water level reaches the top edge 
of the clear viewing area. (Be careful not to
over fill.)

5. Place Water Reservoir base into the left 

side of the Brewer and be sure the 
Water Reservoir Lock Tabs engage 
with the Brewer. Replace Lid on Water
Reservoir.

6. Press Power Button found on upper right

panel of the Brewer. The green light surround-
ing the Power Button will become illuminated.

7. The LCD Control Center will come on and

indicate ‘PRIME’ and the icon for the Large
Cup will flash. If 'NOT READY' appears in

LCD Control Center, be sure the handle is all
the way down. Please note, a K-Cup should
not be used for the Priming Sequence.

8. Press the Large Cup Button below the

flashing Large Cup indicator.

9. The Brewer will automatically fill the Brewer

(priming it) and then the water will be 
heated. This will take about 3 minutes. During
the heating period 'NOT READY' is dis-
played on the LCD Control Center. When the
water is heated, 'READY' will be displayed.

10.Press the Large Cup Button below the

flashing Large Cup Icon to start a cleansing
brew, during which hot water will flow into
your cup or mug. Pour the hot water into
the sink.

11.The Brewer may take 15 seconds to reheat

water between brews and then 'READY' will
again be displayed.

12. The one-time priming process is now 

complete and you are ready to brew!

1. LCD Control Center will indicate ‘READY’.

2. Place a cup or mug on the Drip Tray Plate.

3.  Lift the Handle and the K-Cup Holder will

open toward you.

4. Select a K-Cup

®

portion pack.

5. Place a K-Cup

®

portion pack in the K-Cup

Holder (as shown in exhibit at top of page).

6. Lower the Handle to close the Lid over 

the K-Cup Holder, (when it is closed 
completely, the LCD Control Center will
indicate ‘BREW’ and the large and small
cup icons will blink up to 60 seconds).

7. Choose the amount of coffee or tea you

wish to brew by pressing the button under
the Small Cup or Large Cup Icon that 
indicates your choice. The Large Cup
choice will yield a 7.25 oz serving and 

the Small Cup choice will yield a 
5.25 oz serving.

8. The LCD will now display the word

‘BREWING’ and the serving size 
you selected.

9. There may be a short pause before the

brewing process begins. The process lasts
for approximately 40 seconds and ends
with a burst of air to remove all liquid 
coffee or tea from the K-Cup.

10. Lift the Handle and remove and dispose

of the used K-Cup. 
CAUTION: K-Cup will be hot.

11. Enjoy your first cup of Keurig Brewed

®

gourmet coffee or tea!

12. Your Brewer may display ‘NOT READY’ 

as it heats water for the next brew cycle. 
The ‘READY’ indication will return to the
LCD Control Center in approximately 
15 seconds.

NOTE: You may see small amounts of water
coming from the Vent and dripping into the
Water Reservoir during this and subsequent 
heating – this is normal.

NOTE: Do not remove the foil lid or
puncture the K-Cup

®

portion pack. 

NOTE: If the Water Reservoir is empty or 
not in place on the Brewer, then the LCD
Control Center will also indicate ‘ADD
WATER’. None of the buttons will be activated
until water is added to the Water Reservoir.

the K-Cup Holder and the other in the bottom
of the K-Cup Holder. To avoid risk of injury,
do not put your fingers in the K-Cup Chamber.

NOTE: If you do not push the Brew Buttons

in 60 seconds, the LCD Control Center will
return to ‘READY’ and the Brew Buttons will 
be disabled to prevent accidental activation.
Re-activate the Brew Buttons by raising and
lowering the Handle completely.

CAUTION: There is extremely hot water in
the K-Cup Holder during the brew process.
To avoid risk of injury, do not lift the 
Handle or open the K-Cup Chamber 
during the brew process.

NOTE: If Brewer has been exposed to tempera-
tures below freezing, allow Brewer at least two
hours to reach room temperature before prim-
ing. A frozen or extremely cold brewer will not
prime properly and can cause damage.

MENU

NOTE: Following the brew, your Brewer 

will fill to be ready for the next brew. The
pump will make a vibrating sound. This is
normal.