Arcam preamp processor av8 Manuel D’Utilisation
E-32
E-32
E-33
E
n
g
li
sh
IR REMOTE CODES
The following information is supplied for owners of advanced
programmable remote controls, such as the Philips ‘Pronto’ and similar
devices, where it is possible to program remote codes directly into the
device.
The coding system for the AV8 is based on the Philips RC-5 standard.
The main system control uses RC-5 system code ‘16’, so for example,
to program in a ‘Standby’ command, use the command ‘16-124’.
Zone 2 also uses RC-5 system code 16 as standard, as zone 2 is
normally operated in a separate room using a standard (system code
16) remote control.
Changing the system code for zone 2 (or zone 1) from ‘16’ to ‘19’
is possible, but this is only necessary for non-standard use of zone
2. A specially programmed remote control will be required if the
system code is changed. The CR80 remote control has system code
19 functions only for zone 2 in memory as code ‘1213’. Alternatively,
remote controls such as the Philips ‘Pronto’ can be specially computer
programmed. Consult Arcam customer support about changing the
remote system code.
programmable remote controls, such as the Philips ‘Pronto’ and similar
devices, where it is possible to program remote codes directly into the
device.
The coding system for the AV8 is based on the Philips RC-5 standard.
The main system control uses RC-5 system code ‘16’, so for example,
to program in a ‘Standby’ command, use the command ‘16-124’.
Zone 2 also uses RC-5 system code 16 as standard, as zone 2 is
normally operated in a separate room using a standard (system code
16) remote control.
Changing the system code for zone 2 (or zone 1) from ‘16’ to ‘19’
is possible, but this is only necessary for non-standard use of zone
2. A specially programmed remote control will be required if the
system code is changed. The CR80 remote control has system code
19 functions only for zone 2 in memory as code ‘1213’. Alternatively,
remote controls such as the Philips ‘Pronto’ can be specially computer
programmed. Consult Arcam customer support about changing the
remote system code.
TABLE OF REMOTE CODES
Example for programming; Display = RC-5 code 16–59
Command
Command code
Standby
124
On
123
Power toggle
12
Display
59
Menu
82
Info
55
Mute
119
Un-mute
120
Mute toggle
13
Volume up
16
Volume down
17
Sat input
0
AV input
2
Tuner input
3
DVD input
4
Tape input
5
VCR input
6
CD input
7
Aux input
8
DVD-A input
9
Direct on
78
Direct off
79
Direct toggle
10
Command
Command code
Modes
28
THX modes
32
Effects modes
70
Mono mode
106
Stereo mode
107
Dolby PL 2 Movie mode
108
Dolby PL2 Music mode
109
Dolby Pro Logic Emulation
110
DTS Neo:6 Cinema mode
111
DTS Neo:6 Music mode
112
THX off
113
THX Cinema mode
114
THX Ultra2 Cinema mode
115
THX Music mode
116
THX Surround EX
117
Effect off
63
Effect: Music
64
Effect: Party
65
Effect: Club
66
Effect: Hall
67
Effect: Sport
68
Effect: Church
69
Preset 1
72
Preset 2
73
Preset 3
74
Preset 4
75
Preset 5
76
Nav up
85
Nav down
86
Nav left
81
Nav right
80
OK
87
Trim menu
37
Sub trim
51
Lip sync
50
Restore (“Fav”)
14
Sat video
19
AV video
20
DVD video
22
Tape video
23
VCR video
24
Video type
126