temco-tool dv1000n-p Manuel D’Utilisation
26
Temco DV1000/1200/1400 Series
76657
Thermostatic Fan Kit - Optional
(Part # GDVTFK)
For installation of the optional fan, please refer to the
instructions included in the fan kit.
For installation of the optional fan, please refer to the
instructions included in the fan kit.
Electrical Services
Optional fan kits are equipped with a 120V, 60Hz
blower, less than 12 amps.
If electrical supply 120V is being roughed in to provide
for future installation of an optional blower kit, an ap-
proved surface mount, steel electrical box, cover and
strain relief bushing must be installed in the fireplace
(supplied by others).
NOTE: All electric connections are to be made in ac-
cordance with CSA Standard C22.1 - Canadian Electri-
cal Code part 1 or with the National Electrical Code,
ANSI/NFPA 70 (latest addition) and/or in accordance
with local codes.
blower, less than 12 amps.
If electrical supply 120V is being roughed in to provide
for future installation of an optional blower kit, an ap-
proved surface mount, steel electrical box, cover and
strain relief bushing must be installed in the fireplace
(supplied by others).
NOTE: All electric connections are to be made in ac-
cordance with CSA Standard C22.1 - Canadian Electri-
cal Code part 1 or with the National Electrical Code,
ANSI/NFPA 70 (latest addition) and/or in accordance
with local codes.
TL121
DV1000/DV1200
final position logs
12/11/03 djt
TL121
Fig. 34 DV1000 and DV1200 logs in final position.
TL122
Dv logs
side view
12/11/03 djt
Back Log
Twig
Slot
Bracket
Bracket
Front Log
TL122
Fig. 35 Side view of logset. (NOTE: The side logs for the
DV1400 are not shown.)
DV1400 are not shown.)
Speed Control Switch
1. The blower combination on/off switch and electronic
speed control is supplied loose to allow mounting in
a conveniently located wall mounted electrical box.
a conveniently located wall mounted electrical box.
2. Wire speed control into black (hot) side of 120V,
60Hz line as shown in blower wiring diagram.
M
White
Black
T173
blower wiring
11/14/03 djt
G
Green
120
Volt
Volt
Speed Control
Switch
Temperature
Sensor
Sensor
Fan
T173
Fig. 36 Fan wiring diagram.
CAUTION: Should this fan require servic-
ing, the power supply must be discon-
nected.
ing, the power supply must be discon-
nected.
Millivolt System
CAUTION: At installation and/or after any
service work or repairs glass door must be
removed before proceeding to lighting instruc-
tions.
CAUTION: At installation and/or after any
service work or repairs glass door must be
removed before proceeding to lighting instruc-
tions.
service work or repairs glass door must be
removed before proceeding to lighting instruc-
tions.
CAUTION: At installation and/or after any
service work or repairs glass door must be
removed before proceeding to lighting instruc-
tions.
Burner On/Off Control
All models may be used with an optional wall switch
that turns the main burner on or off. Optional millivolt
thermostats (GFPMT) and remote control may be sub-
stituted for the wall switch (For installation of these op-
tions, detail instructions are provided with optional kits).
CAUTION: If the remote receiver is located in the gas
control area (under the firebox), clearance should be
below the firebox at least 2” (51 mm) to avoid high tem-
peratures (receiver should not be exposed to tempera-
tures exceeding 130°F).
that turns the main burner on or off. Optional millivolt
thermostats (GFPMT) and remote control may be sub-
stituted for the wall switch (For installation of these op-
tions, detail instructions are provided with optional kits).
CAUTION: If the remote receiver is located in the gas
control area (under the firebox), clearance should be
below the firebox at least 2” (51 mm) to avoid high tem-
peratures (receiver should not be exposed to tempera-
tures exceeding 130°F).