temco-tool dv1000n-p Manuel D’Utilisation
28
Temco DV1000/1200/1400 Series
76657
3. Open control access panel.
4. Push in gas control knob slightly and turn clock-
4. Push in gas control knob slightly and turn clock-
wise
to “OFF”. Do not force.
5. Close control access panel.
1. STOP! Read the “For Your Safety” information
first and locate the control panel before lighting.
2. Turn off all electrical power to the fireplace.
3. For MN/MP/TN/TP appliances ONLY, go on
3. For MN/MP/TN/TP appliances ONLY, go on
to Step 4. For other appliances turn the On/Off
switch to “OFF” position or set thermostat to
lowest level.
switch to “OFF” position or set thermostat to
lowest level.
4. Open control access panel.
5. Push in gas control knob slightly and turn clock-
5. Push in gas control knob slightly and turn clock-
wise
to ”OFF”.
9. Turn knob on gas control counterclockwise
to “PILOT”.
10. Push the control knob all the way in and hold.
Immediately light the pilot by repeatedly depress-
ing the piezo spark ignitor until a flame appears.
Continue to hold the control knob in for about one
(1) minute after the pilot is lit. Release knob and it
will pop back up. Pilot should remain lit. If it goes
out, repeat steps 5 through 8.
ing the piezo spark ignitor until a flame appears.
Continue to hold the control knob in for about one
(1) minute after the pilot is lit. Release knob and it
will pop back up. Pilot should remain lit. If it goes
out, repeat steps 5 through 8.
FOR YOUR SAFETY READ BEFORE LIGHTING
instructions.
•
If you cannot reach your gas supplier, call
the Fire Department
the Fire Department
C. Use only your hand to push in or turn the gas con-
trol knob. Never use tools. If the knob will not push
in or turn by hand, do not try to repair it, call a quali-
fied service technician. Force or attempted repair
may result in a fire or explosion.
in or turn by hand, do not try to repair it, call a quali-
fied service technician. Force or attempted repair
may result in a fire or explosion.
D. Do not use this appliance if any part has been un-
der water. Immediately call a qualified service tech-
nician to inspect the heater and to replace any part
of the control system and any gas control which has
been under water.
nician to inspect the heater and to replace any part
of the control system and any gas control which has
been under water.
A. This appliance has a pilot which must be lit
manually. When lighting the pilot follow these
instructions exactly.
instructions exactly.
B. BEFORE LIGHTING smell all around the heater
area for gas. Be sure to smell next to the floor
because some gas is heavier than air and will
settle on the floor.
because some gas is heavier than air and will
settle on the floor.
WHAT TO DO IF YOU SMELL GAS
•
Do not try to light any appliance
•
Do not touch any electric switch
•
Do not use any phone in your building
•
Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
neighbor’s phone. Follow the gas supplier’s
To Turn Off Gas To Heater
Lighting And Operating Instructions
1. Turn the On/Off switch to Off position or set the
thermostat to lowest setting.
2. Turn off all electric power to the fireplace if
service is to be performed.
Lighting Instructions
6. Wait five (5) Minutes to clear out any gas. Then
smell for gas, including near the floor. If you
smell gas, STOP! Follow “B” in the safety infor-
mation above. If you do not smell gas, go to the
next step.
smell gas, STOP! Follow “B” in the safety infor-
mation above. If you do not smell gas, go to the
next step.
7. Remove glass door before lighting pilot. (Refer
to Glass Frame Removal Section)
8. Visibly locate pilot by the main burner.
• If knob does not pop up when released, stop
and immediately call your service technician or
gas supplier.
• If after several tries, the pilot will not stay lit,
gas supplier.
• If after several tries, the pilot will not stay lit,
turn the gas control knob to “OFF” and call your
service technician or gas supplier.
service technician or gas supplier.
11. Replace glass door.
12. Turn gas control knob to “ON” position.
13. For RN/RP appliances turn the On/Off switch to
12. Turn gas control knob to “ON” position.
13. For RN/RP appliances turn the On/Off switch to
“ON” position or set thermostat to desired setting.
14. Turn on all electrical power to the fireplace.
WARNING: If you do not follow these instructions exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
SIT NOVA
PILOT
ON
OFF
ON
PILOT
O
FF
OFF
FP1067
lighting instruction
knobs
3/9/01 djt
5
4
3
2
1
OF
F
Pi
lot
3/8" - 1/2"
FP1068
Lighting instructions
Pilots
Euro SIT
Honeywell