Garmin International Inc 02047 Manuel D’Utilisation

Using a rotary-cutting tool or jigsaw, cut the mounting surface along the

inside of the dashed line on the template.

Place the speaker in the cutout to test the fit.

If necessary, use a file and sandpaper to refine the size of the cutout.

After the speaker fits correctly in the cutout, ensure the mounting holes on

the speaker line up with the pilot holes on the template.

If the mounting holes on the speaker do not line up, mark the new pilot-

hole locations.

Using a 3 mm (

1

/

8

 in.) drill bit, drill the pilot holes.

Remove the template from the mounting surface.

Install the included mounting gasket 

À

 on the back of the speaker.

Make the necessary wiring connections (Connecting the Active Speaker to

the VHF Radio and Handset, page 4).

Place the speaker in the cutout.

Secure the speaker to the mounting surface using the included M4 screws

Á

.

Snap the screw cover 

Â

 in place.

Before drilling a hole to mount the handset connector from the active speaker,

you should mount the active speaker and verify that the cable from the active

speaker is long enough to reach the handset-connector mounting location

(Mounting the Active Speaker, page 2).
If you do not install the active speaker, you must verify that the included

extension cable is long enough to connect to the GHS 11 STATION 1 port on

the VHF radio and to the handset-connector mounting location.
You can use the included hardware to mount the handset connector from the

active speaker on the dashboard or other mounting surface. If you do not

install the active speaker, you can use the hardware to mount the handset

connector from the included extension cable on the dashboard or other

mounting surface.

Using the mounting plate 

À

 as a template, trace the cable hole in the

center of the mounting plate and mark the screw locations.

Set the mounting plate aside.
Do not drill through the mounting plate.

Using a 22 mm (

7

/

8

 in.) drill bit or hole saw, drill the center cable hole 

Á

 in

the mounting surface.

Using a 3 mm (

1

/

8

 in.) drill bit, drill the pilot holes.

Apply marine sealant between the mounting plate and the mounting

surface to help seal the holes (optional).

Using the included screws, attach the mounting plate to the mounting

surface.

Select an option:
• If you installed the active speaker, route the long cable from the active

speaker to the connector mounting location.

• If you did not install the active speaker, connect the female end of the

included extension cable to the GHS 11 STATION 1 port on the VHF

radio, and route the male end of the extension cable to the connector

mounting location.

Feed the connector 

Â

 through the back of the mounting surface.

Apply marine sealant around the connector in the mounting plate to help

seal the hole (optional).

Secure the connector to the mounting plate using the weather cap 

Ã

 and

the nut 

Ä

.

This device should be mounted in a location that is not exposed to extreme

temperatures or conditions. The temperature range for this device is listed in

the product specifications. Extended exposure to temperatures exceeding the

specified temperature range, in storage or operating conditions, may cause

device failure. Extreme-temperature-induced damage and related

consequences are not covered by the warranty.

• You must install the primary handset (connected to the GHS 11 STATION

1 port) in the wheelhouse or an adjacent room, in accordance with FCC

law.

• To avoid interference with a magnetic compass, do not install the handset

closer than 60 cm (23.6 in.) to a compass.

• If you do not install the active speaker, you can use the included 10 m

(32 ft.) extension cable to connect the handset to the VHF radio. You must

select a mounting location for the handset where you can connect the

extension cable to the handset and to the GHS 11 STATION 1 port on the

VHF radio. If needed, additional extension cables are available from your

Garmin dealer.

• You can use the included screws to mount the handset connector and the

handset cradle mount on your boat. If the included screws are not

appropriate for the mounting surface, you must purchase suitable

hardware.

You should install the handset connector in the mounting surface before

installing the handset cradle (Installing the Handset Connector in the Mounting

Surface, page 3).

Select a mounting location for the handset cradle near the handset

connector.
TIP: To help determine the best location, you can place the handset in the

cradle, connect the handset to the connector, and hold it against the

mounting surface.

Using the cradle as a template, mark the screw locations.

Set the cradle aside.
Do not drill through the cradle.

Using a 3 mm (

1

/

8

 in.) drill bit, drill the pilot holes.

Using the included M3.5 screws, secure the cradle to the mounting

surface.

You must connect the VHF 315 radio to power, to a GHS 11 handset, a VHF

antenna, and a GPS source. When making connections to the device, observe

the following considerations.
• You must connect the primary handset (installed in the wheelhouse or

adjacent room, in accordance with FCC law) to the GHS 11 STATION 1

port.

• You can connect up to three handsets to the radio. You can purchase

additional handsets from your Garmin dealer.

• You can install the included active speaker (optional) in-line with any

handset connected to the radio. You can purchase additional active

speakers from your Garmin dealer.

Installation Instructions

3