Advance Security Inc TR06AM Manuel D’Utilisation

MAY/23/ 2003 

RST771IN 

14 

 

Cut Existing Unlock Wire

Lock

Unlock

OEM Door Master Lock Switch

To All Other
Door Lock
Motors

Pink Wire

OEM Driver's
Door Lock
Motor

Existing Neg.
Lock Wire

Existing Neg.

Unlock Wire

86

30

85

87

87A

+ 12V

Green Wire
Door Lock

Blue Wire
Door Unlock

OEM Door
Lock Relay

H8/8:
10-Pin
Plug
From
Alarm

H6:
3 Pin
Plug
To
Alarm

 

 

Cut Existing Unlock Wire

X

Lock

Unlock

OEM Door Master Lock Switch

To All Other
Door Lock
Motors

Pink Wire

OEM Driver's
Door Lock
Motor

+ 12V

Existing Pos.
Lock Wire

Existing Pos.
Unlock Wire

30

87A

87

86

85

+12V

+ 12V

OEM Door
Lock Relay

86

30

85

87

87A

Green Wire
Door Unlock

Blue Wire Door Lock

H8/8:
10-Pin
Plug
From
Alarm

H6:
3 Pin
Plug
To
Alarm

 

A. PROGRAMMING TRANSMITTER: 

Note: This mode will only retain the last 4 remote transmitters programmed. If the transmitter memory is 
exceeded, the security system will start deleting transmitters from memory in chronological order. 
Enter:  
1. Turn the Ignition switch ‘OFF/ON’ 3 TIMES and stay in ON position. Within 15 seconds. 
2. Push the Valet switch 3 times and hold it until a long chirp is hearing then release the valet switch. You 

are now in the Transmitter programming mode. 

Program: 
1. Press button on one of the transmitter until the siren responds with a confirming chirp the first transmitter 

is now programmed.     

2. Press button on the second transmitter until the siren responds with a confirming chirp, the second 

transmitter is now programmed.     

3. Apply the same procedure to program 3rd and 4th

. 

Exit:  Turn Ignition to 'OFF' position, or leave it for 15 seconds. A 3 long chirps & 3 parking light flashes to 
confirm exit. 
 

B. FEATURES PROGRAMMING: 

1. Turn the Ignition switch ‘ON/OFF’ 3 TIMES and stay in OFF position.   
2. Push the Valet switch 2 times and hold it until one chirp with a long chirp is hearing then release the valet 

switch. You are now in the Alarm feature ‘I’ programming mode. 

3. Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.   

a. The siren chirps and LED pause will indicate previously setting. 
b. The factory default settings is always [1] LED flash, [1] chirp. 

4  Depress the transmitter button ‘A’ again to change the feature. Simple keep re-depressing the transmitter 

button ‘A’ again until the module advances to your desired setting. 

a. In this case, Press button ‘A’ again, the module would advance to [2] LED flash, [2] chirps. 
b. Press button ‘A’ again, the module would advance to [3] LED flash, [3] chirps etc. 

5. Depress the transmitter button ‘B’ corresponding to the feature ‘B’ you wants to program. 
For example: To program the arming mode form “Active arming” to “Passive Arming with Passive Door 
Locking”, After “Arming mode” program, the next program is “Rearm on/off” .………. 
1  Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.   
2  Push the Valet switch 2 times and hold it until a chirp with a long chirp is hearing then release the valet 

switch.