Tyco Safety Products/Sensormatic AMS1080 Manuel D’Utilisation
AMS-1080 DETECTION SYSTEM
8200-0418-01, REV. A
INSTALLATION AND SERVICE GUIDE
11 of 18
To a Railing Post
For this installation, the antenna is secured to a
railing post between two adjacent aisles.
railing post between two adjacent aisles.
Tools required:
- Two 3.2mm (1/8in) Allen wrench hex drivers
- Tape
- Tape
measure
- Pencil or marker
- Electric drill and drill bits: 5.5mm (7/32in) and 9.5mm
- Electric drill and drill bits: 5.5mm (7/32in) and 9.5mm
(3/8in)
- Phillips-head screwdriver or bit
- Hand vacuum or broom
- Trenching tool, such as a floor saw
- Hand vacuum or broom
- Trenching tool, such as a floor saw
Parts required:
Install Kit 0352-0198-01
Bracket, pole
4
0505-0570-01
Bushing, pole
4
0505-0571-01
Appliqué 4
0505-0572-01
Screw, M, PHP, M5x16
2
5801-3081-120
Washer, FL, M5
4
5840-0400-022
Nut, M5
2
5827-0400-020
Clamp, cable, 1/2in width, SS
2
6010-0122-01
PROCEDURE
1. Saw a 6.4mm (1/4in) wide, 19mm (3/4in) deep
trench into the floor between the railing post and
the counter where the controller is to be located.
the counter where the controller is to be located.
2. With the label on the bottom side panel of the
antenna facing Aisle A1 or Aisle B1, with the
antenna parallel to the line of traffic and its
bottom 17.8cm (7in) from the floor, drill a 16mm
(5/8in) cable access hole in the railing post
directly opposite where cables exit the antenna.
antenna parallel to the line of traffic and its
bottom 17.8cm (7in) from the floor, drill a 16mm
(5/8in) cable access hole in the railing post
directly opposite where cables exit the antenna.
CAUTION: Do not drill this hole
through the other side of the post.
through the other side of the post.
3. Attach the pole bracket to the antenna.
a. Remove an M5x16 screw, washer, and nut
from the pole bracket and loosen the strap,
but be careful to keep the bracket assembly
together.
but be careful to keep the bracket assembly
together.
b. Slide the pole bracket down the post to align
the cable exit hole in the bracket with the
cable access hole in the post.
cable access hole in the post.
c. Spread the bracket assembly.
d. Insert the pole bracket into the part of the
antenna designated for it while routing
antenna cables into the access hole, down
inside the post, and into the trench.
antenna cables into the access hole, down
inside the post, and into the trench.
e. Reattach the M5x16 screw, washer, and nut
and tighten the assembly.
f. With its screw tucked inside the pole bracket,
tighten the strap holding the bracket
together.
together.
4. Remove the backing from the appliqué. Then
affix the appliqué over its matching recess in the
pole bracket to hide the hardware.
pole bracket to hide the hardware.
5. Repeat steps 3 and 4 to install a second pole
bracket about 15.2cm (6in) above the first.
6. Route antenna cables through the trench to the
controller. Connect antenna cables to the
controller. DO NOT CUT CABLES!
controller. DO NOT CUT CABLES!
7. Install Ranger antennas.
Screw
Strap
Remove hardware
to attach
to attach
17.8cm (7in)
Trench