Tyco Safety Products/Sensormatic AMS9050 Manuel D’Utilisation
Preliminary
Installation
The AMC-7000 Metal Foil Detection kit (ZPMETAL-
DET) consists of the following:
DET) consists of the following:
Part Qty.
Part
Number
Metal detection enclosure
1
0304-3048-01
Mounting bracket, Left
1
0505-4642-01
Mounting bracket, Right
1
0505-4642-02
Tx/Rx cable
2
0652-0467-02
Power supply/RS-485 cable
2
0652-0468-01
Wired Sync
1
0652-0467-01
Connector assy, Aux/WS (5-pin)
2
0304-2887-01
Connector assy, Alarm/comm (8-pin) 1
0304-2952-01
Romex conduit connector
4
6010-0107-01
Nut 4
5828-0400-011
For Pre-existing Systems
If you are installing an AMC-7000 on a Ultra•Exit
system that is already installed and working, do the
following before turning off the system and starting
the installation process.
system that is already installed and working, do the
following before turning off the system and starting
the installation process.
1. Perform a tag-pick test so that you can compare
system performance afterwards.
2. Use a tag or label to determine which pedestal
is A and which is C. Use the noise screen on
the configurator to determine which is which.
the configurator to determine which is which.
3. Save the system settings to a file.
Wiring the AMC-7000
Connect the following cables to the AMC-7000
Metal Foil Detection Board. Use the four Romex
conduit connectors when connecting the cables to
the AMC-7000 enclosure. Refer to Figure 1 and
Figure 2.
Metal Foil Detection Board. Use the four Romex
conduit connectors when connecting the cables to
the AMC-7000 enclosure. Refer to Figure 1 and
Figure 2.
AMC-7000
Connector
Connector
Cable P/N and Name
P2
(Ant. 1 OUT)
0652-0242-01
(AMS-9050 Tx/Rx)
(AMS-9050 Tx/Rx)
P1
(Ant. 1 IN)
0652-0467-02
(AMC-7000 Tx/Rx)
(AMC-7000 Tx/Rx)
P8
(+12V DC GND)
0652-0468-01
(AMC-7000 Power Cable)
(AMC-7000 Power Cable)
P14
(Network RS485)
0652-0468-01
(AMC-7000 Power/RS-485)
(AMC-7000 Power/RS-485)
P5
(Wired Sync)
0652-0467-01
(AMC-7000 Wired Sync)
(AMC-7000 Wired Sync)
P3
(Ant. 2 IN)
0652-0467-02
(AMC-7000 Tx/Rx)
(AMC-7000 Tx/Rx)
P4
(Ant. 2 OUT)
0652-0242-01
(AMS-9050 Tx/Rx)
(AMS-9050 Tx/Rx)
P6/P7
1
(Peripheral RS-485)
RS-485
P9
2
(Relay)
Relay
1 This connector is cabled only when the AMC-
7000 is connected to an RS-485 network.
2 This connector is cabled only when the AMC-
7000 is connected to an optional relay-activated
device (such as a security camera or paging
device).
device (such as a security camera or paging
device).
Wiring the Ultra•Exit Antennas
Connect the following cables to the Ultra•Exit
antennas. Refer to Figure 1.
antennas. Refer to Figure 1.
Connector
Cable P/N and Name
P5 on Ant. A
(Alarm/Com)
0652-0243-01 (AMS-9050 Com)
from P92 on AMS-9050
from P92 on AMS-9050
P1 on Ant. A
(Tx/Rx)
0652-0242-01 (AMS-9050 Tx/Rx)
from P2 on AMC-7000
from P2 on AMC-7000
P5 on Ant. C
(Alarm/Com)
0652-0243-01 (AMS-9050 Com)
from P93 on AMS-9050
from P93 on AMS-9050
P1 on Ant. C
(Tx/Rx)
0652-0242-01 (AMS-9050 Tx/Rx)
from P4 on AMC-7000
from P4 on AMC-7000
AMC-7000 INTEGRATED METAL Foil DETECTION
8200-2609-01, REV. 3a
INSTALLATION GUIDE
18 OF 31