Tyco Safety Products/Sensormatic IDRDR2 Manuel D’Utilisation
AGILE2 READER
8200-0222-08, REV. A
INSTALLATION AND SERVICE GUIDE
6 of 13
Configure the Reader
In some cases, the application software may
provide support for reader configuration. If so,
follow the instructions provided with the application.
provide support for reader configuration. If so,
follow the instructions provided with the application.
The following procedure describes how to
configure the reader directly from a network PC
using the browser-based interface.
configure the reader directly from a network PC
using the browser-based interface.
The reader is shipped with the following default
network configuration:
network configuration:
IP Address:
10.0.0.101
Subnet Mask:
255.0.0.0
Gateway: 10.0.0.1
You must know the IP address and subnet mask
settings for the network environment in which the
reader will be running.
settings for the network environment in which the
reader will be running.
1. Exit any reader applications that are running on
the network.
IMPORTANT: Running another reader
application while using the browser-based
interface may cause a reader error. If this
happens, reboot the reader or restart the
system using the browser-based interface.
application while using the browser-based
interface may cause a reader error. If this
happens, reboot the reader or restart the
system using the browser-based interface.
2. Verify that the reader is operational. All LED’s
should be out except for the green power LED
which should be blinking.
which should be blinking.
3. Start a Java-enabled web browser from any
network-enabled PC.
This PC must be configured with an IP address
and subnet mask compatible with the reader
default settings. For example:
and subnet mask compatible with the reader
default settings. For example:
IP address:
10.0.0.10
Subnet mask: 255.0.0.0.
4. Browse to…
http://10.0.0.101
The Agile2 Reader Tagreader browser-based
interface to the tagreader appears.
interface to the tagreader appears.
5. Click the Settings link in the navigation menu.
The Modify Settings page appears.
6. These setting apply to both the LAN interface
and the wireless interface. If you wish to use
DHCP select the DHCP? Yes radio button;
otherwise, enter the required network settings in
the IP Address, Subnet Mask, and Gateway
fields. The fields will turn red if the gateway is
not on the same subnet as the IP address.
Then, click the Save Changes button.
DHCP select the DHCP? Yes radio button;
otherwise, enter the required network settings in
the IP Address, Subnet Mask, and Gateway
fields. The fields will turn red if the gateway is
not on the same subnet as the IP address.
Then, click the Save Changes button.
IMPORTANT: Do not disconnect power until the
save process is complete.
save process is complete.
7. Verify that the settings shown are correct. Then,
restart the reader by disconnecting the power
cable and then reconnecting it (see Rebooting
the Reader on page 11).
cable and then reconnecting it (see Rebooting
the Reader on page 11).
It may take several seconds for the reader to
restart. If the IP address was changed, you
must type the new address into the browser
address field to communicate with the reader.
restart. If the IP address was changed, you
must type the new address into the browser
address field to communicate with the reader.
8. Once the system restarts, click Save Changes.
You are taken to the Settings Modified page.
Your changes will be saved and then applied.
After the reader reconfigures its network
interfaces, it will automatically redirect you to its
status page. There is no need to restart the
reader.
Your changes will be saved and then applied.
After the reader reconfigures its network
interfaces, it will automatically redirect you to its
status page. There is no need to restart the
reader.
IMPORTANT: Do not disconnect power while
the reader is saving its new configuration.
the reader is saving its new configuration.
The reader is now ready to receive commands
from the network.
from the network.
9. Use the Query page of the browser-based
interface to verify antenna operation.
10. Close the browser window. Start the reader
application on the network.