Avnet Inc AVTEG001 Manuel D’Utilisation
26
26
AES-BCM4343W-M1-G Datasheet
802.11 b/g/n WLAN, Bluetooth & BLE SoC Module
User manuals shall display the following Industry Canada notices in a conspicuous location:
11.5 OEM Instructions
This module has been certified for installation into products only by OEM integrators under the following
conditions:
conditions:
The antennas used with this module must be installed to provide a separation distance of at least 20cm
from all persons, and must not be co-located or transmit simultaneously with any other antenna or
transmitter, except in accordance with FCC multi transmitter product procedures.
from all persons, and must not be co-located or transmit simultaneously with any other antenna or
transmitter, except in accordance with FCC multi transmitter product procedures.
11.6 OEM Labeling Requirements
A clearly visible label is required, affixed to
the outside of the user’s (OEM) enclosure.
This label should display the following:
11.7 Limitations
This product is not intended for use in safety-critical applications (such as life support) where a failure
of the Avnet product could be expected to cause severe personal injury or death.
of the Avnet product could be expected to cause severe personal injury or death.
Contains FCC ID: 2AF62-AVTEG001
Contains IC: 21571-AVTEG001
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired operation.
Contains IC: 21571-AVTEG001
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired operation.
Industry Canada Statements
This Device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to
the following two conditions: (1) this device may not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired operation of the device.
the following two conditions: (1) this device may not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts
de licence. L'exploitation est autorisée aux deux onditions suivantes: (1) l'appareil ne doit pas produire
de brouillage, et (2) l'utilisateur de l'appa-reil doit accepter tout brouillage radioélectrique subi, meme si
le brouillage est susceptible d'en com-promettre le fonctionnement.
de licence. L'exploitation est autorisée aux deux onditions suivantes: (1) l'appareil ne doit pas produire
de brouillage, et (2) l'utilisateur de l'appa-reil doit accepter tout brouillage radioélectrique subi, meme si
le brouillage est susceptible d'en com-promettre le fonctionnement.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type
and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential
radio interference to other users, the antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (EIRP) is not more than that necessary for successful
communication.
Conformément à la réglementation d'Industrie Can-ada, le présent émetteur radio peut fonctionner avec
une antenne d'un type et d'un gain maximal (ou infé-rieur) approuvé pour l'émetteur par Industrie Can-
ada. Dans le but de réduire les risques de brouil-lage radioélectrique à l'intention des autres utilisa-
teurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée
équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication
satisfaisante.
and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential
radio interference to other users, the antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (EIRP) is not more than that necessary for successful
communication.
Conformément à la réglementation d'Industrie Can-ada, le présent émetteur radio peut fonctionner avec
une antenne d'un type et d'un gain maximal (ou infé-rieur) approuvé pour l'émetteur par Industrie Can-
ada. Dans le but de réduire les risques de brouil-lage radioélectrique à l'intention des autres utilisa-
teurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée
équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication
satisfaisante.