Viessmann 4501 H0 4501 Fiche De Données
Codes de produits
4501
6
rt bn rt 1 gn rt 2 gn
ON
1
2
3
4
5
6
7
8
WP
Viessmann
5211
Magnetartikeldecoder
rt bn E gn 4 rt gn 3 rt
Diode
16 V ~ / =
16 V ~ / =
braun
grün
rot
blau
gelb
z. B. 5211
gelb
Digitalzentrale
Optional:
separater Anschluss des
separater Anschluss des
Lichtstroms.
Widerstand
brown
green
red
blue
yellow
e. g. 5211
diode
resistor
Digital Command Station
Option:
separate power
separate power
supply for lights
yellow
Abb. 6
Fig. 6
Analoge Ansteuerung
Abbildung 7 zeigt, wie einfach Sie die zweibegrif-
Abbildung 7 zeigt, wie einfach Sie die zweibegrif-
figen Formsignale mit Hilfe der Viessmann Tasten-
stellpulte 5547 (ohne Rückmeldung) oder 5549
(mit Rückmeldung durch LEDs) anschließen kön-
nen. Schalter, Taster und Relais anderer Herstel-
ler können Sie natürlich auch verwenden.
stellpulte 5547 (ohne Rückmeldung) oder 5549
(mit Rückmeldung durch LEDs) anschließen kön-
nen. Schalter, Taster und Relais anderer Herstel-
ler können Sie natürlich auch verwenden.
Digitale Ansteuerung
Viessmann-Formsignale können auch von einem
Digitalsystem angesteuert werden (Abb. 6). Beim
Anschluss z. B. an den
Viessmann-Formsignale können auch von einem
Digitalsystem angesteuert werden (Abb. 6). Beim
Anschluss z. B. an den
Viessmann-Magnetartikel-
Decoder 5211 (Märklin / Motorola) müssen Sie da-
rauf achten, dass neben den blauen Kabeln zur
Signalsteuerung auch das gelbe Kabel (ohne Mar-
kierung) für die Stromversorgung angeschlossen
rauf achten, dass neben den blauen Kabeln zur
Signalsteuerung auch das gelbe Kabel (ohne Mar-
kierung) für die Stromversorgung angeschlossen
ist. Zum digitalen Schalten eines zweibegriffigen
Signals wird eine Ausgangsgruppe eines Magnet-
artikeldecoders benötigt (s. Abb. 6).
Signals wird eine Ausgangsgruppe eines Magnet-
artikeldecoders benötigt (s. Abb. 6).
Der 5211 (4-fach) ist kompatibel zum Märklin / Mo-
torola und Märklin-Systems-Format. Der 5212 (4-
fach) ist kompatibel zu allen DCC-Digitalsystemen
wie z. B. Digital plus (Lenz), Arnold Digital, Roco
Digital, Fleischmann Twin Center, Digitrax, Uhlen-
brock Intellibox, Tillig Digital usw.
torola und Märklin-Systems-Format. Der 5212 (4-
fach) ist kompatibel zu allen DCC-Digitalsystemen
wie z. B. Digital plus (Lenz), Arnold Digital, Roco
Digital, Fleischmann Twin Center, Digitrax, Uhlen-
brock Intellibox, Tillig Digital usw.
Analogue Wiring
The conventional wiring is shown in figure 7. It
shows how you can connect the two-aspect form
signals to a push-button panel (e. g.
The conventional wiring is shown in figure 7. It
shows how you can connect the two-aspect form
signals to a push-button panel (e. g.
Viessmann
5547 or 5549).
Power is supplied via the brown wire and the two
yellow wires. The blue wires with the coloured
markings are connected to contacts (single mo-
mentary switches, track contacts, automatic track
switches, control panel), which in turn are wired to
the brown lead ( = “ground”). Never supply power
to more than one blue wire at the same time.
Power is supplied via the brown wire and the two
yellow wires. The blue wires with the coloured
markings are connected to contacts (single mo-
mentary switches, track contacts, automatic track
switches, control panel), which in turn are wired to
the brown lead ( = “ground”). Never supply power
to more than one blue wire at the same time.
The red wires are used to connect the insulated
track section to the signal contacts (train control).
track section to the signal contacts (train control).
Digital Control
The semaphore signals can also be operated with
a digital system. Refer to figure 6 on the following
page for the correct wiring.
page for the correct wiring.
Simply connect the wires to a digital decoder (e.g.
Viessmann 5211 for Märklin / Motorola format.
5212 is suitable for the NMRA DCC format.
5212 is suitable for the NMRA DCC format.