Firstech, LLC. P2W900FMR Manuel D’Utilisation
13
Tap button (II) for 0.5 seconds to trigger auxiliary output 1. Tap button (III) for 0.5 seconds to
trigger auxiliary output 2. The remote will beep once and the aux icon will illuminate indicating
that the auxiliary outputs have been triggered.
By default, the system is in secure auxiliary mode, which requires you to tap button (IV) for 0.5 seconds
prior to triggering auxiliary 1 or 2. To turn off secure auxiliary, ask your authorized CompuStar dealer to
turn on Option 4-5 to setting II.
trigger auxiliary output 2. The remote will beep once and the aux icon will illuminate indicating
that the auxiliary outputs have been triggered.
By default, the system is in secure auxiliary mode, which requires you to tap button (IV) for 0.5 seconds
prior to triggering auxiliary 1 or 2. To turn off secure auxiliary, ask your authorized CompuStar dealer to
turn on Option 4-5 to setting II.
Temperature and Battery Query
When in range of your vehicle, the remote will display the vehicle’s temperature, battery voltage
and remote battery voltage upon taping button (IV). The temperature will be displayed after
taping button (IV) for 0.5 seconds. Tab button (IV) a second time within four seconds to display
the vehicle’s battery voltage. Tab button (IV) a third time within four seconds to display the
remote’s battery voltage.
and remote battery voltage upon taping button (IV). The temperature will be displayed after
taping button (IV) for 0.5 seconds. Tab button (IV) a second time within four seconds to display
the vehicle’s battery voltage. Tab button (IV) a third time within four seconds to display the
remote’s battery voltage.
If you tap button (IV) and you do not get any response from the remote, the remote pager is most likely
out of range to receive commands.
Silent Arm/Disarm
Upon lock/arm and unlock/disarm, you can eliminate vehicle’s audible confirmation by muting
the siren. Normally, the siren will chirp once to indicate the system is locked/armed and twice
to indicate the system is unlocked/disarmed. To mute the siren tap buttons (I+II) simultaneously for 0.5
seconds. When the siren is muted, the siren icon will no longer be displayed on the LCD. IMPORTANT:
Even when the siren is muted, it will still go off in the event the alarm is triggered.
the siren. Normally, the siren will chirp once to indicate the system is locked/armed and twice
to indicate the system is unlocked/disarmed. To mute the siren tap buttons (I+II) simultaneously for 0.5
seconds. When the siren is muted, the siren icon will no longer be displayed on the LCD. IMPORTANT:
Even when the siren is muted, it will still go off in the event the alarm is triggered.
Remote Mute/Vibration Mode
All CompuStar PRO two-way LCD remotes have the option to be muted. To make the remote silent you
must turn on vibration mode;
STEP 1: Enter remote programming mode by holding down buttons (II + III) simultaneously for 2.5
seconds. The remote will beep once and the LCD will read “Pro9” to indicate that you have successfully
entered programming mode.
STEP 2: Scroll through the remote options by taping button (IV) for 0.5 seconds. To set
vibration mode tap button (IV) five times, or until the vibration mode icon is flashing. If
programming the P2WSHLCDR, simply tap button (IV) one time for 0.5 seconds after entering remote
programming mode.
STEP 3: Once the vibration icon is flashing, turn the feature on or off by taping button (I) for 0.5 seconds.
Exit remote programming by holding down buttons (II + III) simultaneously for 2.5 seconds. The remote
will beep three times indicating that you have successfully exited programming. The vibration icon will
remain illuminated on the LCD indicating the remote is in remote mute/vibration mode.
must turn on vibration mode;
STEP 1: Enter remote programming mode by holding down buttons (II + III) simultaneously for 2.5
seconds. The remote will beep once and the LCD will read “Pro9” to indicate that you have successfully
entered programming mode.
STEP 2: Scroll through the remote options by taping button (IV) for 0.5 seconds. To set
vibration mode tap button (IV) five times, or until the vibration mode icon is flashing. If
programming the P2WSHLCDR, simply tap button (IV) one time for 0.5 seconds after entering remote
programming mode.
STEP 3: Once the vibration icon is flashing, turn the feature on or off by taping button (I) for 0.5 seconds.
Exit remote programming by holding down buttons (II + III) simultaneously for 2.5 seconds. The remote
will beep three times indicating that you have successfully exited programming. The vibration icon will
remain illuminated on the LCD indicating the remote is in remote mute/vibration mode.
Shock Sensor On/Off
Hold buttons (I+III) simultaneously for 2.5 seconds to turn on and off the shock sensor. The
remote will beep twice and the shock sensor icon will illuminate to confirm the shock sensor is
off. The remote will beep once and the shock sensor icon will disappear to confirm the shock
sensor is on. IMPORTANT: Turning off the shock sensor also turns off the optional sensor.
remote will beep twice and the shock sensor icon will illuminate to confirm the shock sensor is
off. The remote will beep once and the shock sensor icon will disappear to confirm the shock
sensor is on. IMPORTANT: Turning off the shock sensor also turns off the optional sensor.