Firstech, LLC. P2W900FMR Manuel D’Utilisation
15
STEP 1: Enter remote programming mode by holding down buttons (II + III) simultaneously for 2.5
seconds. The remote will beep once and the LCD will read “Pro9” to indicate that you have successfully
entered programming mode.
STEP 2: Scroll through the remote options by taping button (IV) for 0.5 seconds. To set the
alarm clock tap button (IV) two times, or until the timer and clock icons are flashing.
STEP 3: Once the timer and clock icons are flashing, set the desired alarm clock time by taping button (I)
for 0.5 seconds to adjust the hour and button (II) for 0.5 seconds to adjust the minute.
STEP 4: Once the time is set, tap button (IV) for 0.5 seconds to scroll to the next remote option. By
default the alarm mode is off. Tap button (I) for 0.5 seconds to turn the alarm clock mode on.
STEP 5: Exit remote programming by holding down buttons (II + III) simultaneously for 2.5 seconds. The
remote will beep three times indicating that you have successfully exited programming. The alarm clock
icon will remain illuminated on the LCD indicating the remote is in alarm clock mode.
seconds. The remote will beep once and the LCD will read “Pro9” to indicate that you have successfully
entered programming mode.
STEP 2: Scroll through the remote options by taping button (IV) for 0.5 seconds. To set the
alarm clock tap button (IV) two times, or until the timer and clock icons are flashing.
STEP 3: Once the timer and clock icons are flashing, set the desired alarm clock time by taping button (I)
for 0.5 seconds to adjust the hour and button (II) for 0.5 seconds to adjust the minute.
STEP 4: Once the time is set, tap button (IV) for 0.5 seconds to scroll to the next remote option. By
default the alarm mode is off. Tap button (I) for 0.5 seconds to turn the alarm clock mode on.
STEP 5: Exit remote programming by holding down buttons (II + III) simultaneously for 2.5 seconds. The
remote will beep three times indicating that you have successfully exited programming. The alarm clock
icon will remain illuminated on the LCD indicating the remote is in alarm clock mode.
Car Call/RPS (Remote Paging Sensor)
The car call/RPS feature uses a remote paging sensor that is designed to be mounted on the inside of
the windshield. After the RPS has been triggered, the car call icon will illuminate and the remote will ring
several times if the remote is in range to receive commands. To trigger the car call or RPS sensor, you
must knock on the windshield in front of the RPS at least two times. The switch on the RPS will adjust
paging sensitivity – the smaller the dot represents the least sensitive setting. Use a key or pen for best
results. If you do not want the remote to receive pages from the RPS, follow the below steps to turn the
feature off;
STEP 1: Enter remote programming mode by holding down buttons (II + III) simultaneously for 2.5
seconds. The remote will beep once and the LCD will read “Prog” to indicate that you have successfully
entered programming mode.
STEP 2: Scroll through the remote options by taping button (IV) for 0.5 seconds. Tap button
(IV) four times, or until the car call icon is flashing.
STEP 3: Once the car call icon is flashing, you can turn the feature off by tapping button (I) for 0.5
seconds. Repeat this step to turn the car call feature back on.
STEP 4: Exit remote programming by holding down buttons (II + III) simultaneously for 2.5 seconds. The
remote will beep three times indicating that you have successfully exited programming. The car call icon
will no longer be illuminated on the LCD indicating that the remote is not in car call mode.
the windshield. After the RPS has been triggered, the car call icon will illuminate and the remote will ring
several times if the remote is in range to receive commands. To trigger the car call or RPS sensor, you
must knock on the windshield in front of the RPS at least two times. The switch on the RPS will adjust
paging sensitivity – the smaller the dot represents the least sensitive setting. Use a key or pen for best
results. If you do not want the remote to receive pages from the RPS, follow the below steps to turn the
feature off;
STEP 1: Enter remote programming mode by holding down buttons (II + III) simultaneously for 2.5
seconds. The remote will beep once and the LCD will read “Prog” to indicate that you have successfully
entered programming mode.
STEP 2: Scroll through the remote options by taping button (IV) for 0.5 seconds. Tap button
(IV) four times, or until the car call icon is flashing.
STEP 3: Once the car call icon is flashing, you can turn the feature off by tapping button (I) for 0.5
seconds. Repeat this step to turn the car call feature back on.
STEP 4: Exit remote programming by holding down buttons (II + III) simultaneously for 2.5 seconds. The
remote will beep three times indicating that you have successfully exited programming. The car call icon
will no longer be illuminated on the LCD indicating that the remote is not in car call mode.
RPS (Remote Paging Sensor) Unlock/Disarm
Basic RPS and car call functions do not require programming, however in order for the sensor to
unlock/disarm the vehicle you must perform the following procedures;
unlock/disarm the vehicle you must perform the following procedures;
STEP 1: Disarm/unlock the alarm (remote must be programmed first)
STEP 2: Turn ignition key to the “on” position and the leave the driver’s door open.
STEP 3: Knock on the windshield in front of the RPS a total of 10 times (each time you knock the LED on
the RPS will flash RED). The LED will begin to flash rapidly in BLUE with successful completion of this
step.
STEP 2: Turn ignition key to the “on” position and the leave the driver’s door open.
STEP 3: Knock on the windshield in front of the RPS a total of 10 times (each time you knock the LED on
the RPS will flash RED). The LED will begin to flash rapidly in BLUE with successful completion of this
step.